Appliance Spares
Quick answer: Own a Samsung front loader (WW or older WF), WA top loader or WD washer-dryer combo? The parts that fail most are the door seal, the drum spider and bearing kit, the drain pump and the water inlet valve; on WA top loaders it is the four suspension rods. All are stocked in Australia and dispatched from Sydney the day you order (12pm Sydney cut-off). What matters is matching the model number on the sticker inside the door rim or on the back panel.
Last updated September 2026
Which Samsung washer have you got?
The WW front loader has stopped with a tub full of water and 5C on the display. The spin sounds like a jet taking off. The WA top loader has walked across the tiles. Each has a usual suspect, and most are parts you can have on the bench in a day or two.
Samsung’s Australian washers fall into four families:
- WW — current front loaders (WW75T, WW85T, WW95N, WW10T, WW12TP, plus the older H, J and K series).
- WF — older front loaders (WF1752, WF1804, WF8750).
- WA — top loaders (WA85N, WA10J, WA11M8700).
- WD — washer-dryer combos (WD75M, WD85T, WD90T, WD10F).
Everything below is from our Samsung parts range; each family has a page in the Samsung model index.
Symptom to part: the Samsung master table
Find your symptom on the left; the model numbers in each link are the ones that part is listed for.
| What you’re seeing | What it usually is | The part |
|---|---|---|
 Banging on spin, drum rocks up and down, rust streaks on the washing | A cracked drum spider — the alloy arm behind the drum corrodes | Samsung Washing Machine Spider WW85T504DAE WW75K54E0UW WW90T504DAW WW90T604DAB |
 A roar that builds with spin speed, grey grease under the machine | Worn drum bearings and lip seal | Samsung Washing Machine Seal & Bearings Kit WW95N54F5PWSA WW95N64FRPW |
 Black mould in the grey rubber, a smell that survives every wash, drips under the door | The door seal — mould gets into the folds, then it tears | Samsung Washing Machine Door Seal WW75T504DTW WW80T4040CE WW85T504DA |
 5C or 5E, water left in the drum, pump hums or is silent | The drain pump, once filter and hose are proven clear | Samsung Washing Machine Drain Pump Assy |
 4C or 4E, slow or no fill on a WA top loader, taps open | The water inlet valve — a coil fails or grit jams it | Samsung Washing Machine water inlet valve WA85N6750BW/SA, WA85N6750BV/SA |
 WA top loader walks, thumps on spin or throws an unbalance code on a normal load | Tired suspension rods — the dampers wear out | 4 x Samsung Washing Machine Suspension Rod Kit WA11M8700GV/SA WA11M8700GW/SA |
 WD combo banging on spin, rust drips, drum grinding | The drum spider, as on the WW | Samsung Washing Machine Spider WD85T554DBW WD85T654DSE WD90T554DBW |
WW front loaders: door seals, spiders and bearings
Door seals by size and series
The seal is chosen by series, not kilos alone. The T-series seal in the table covers the WW75T504 and WW85T504 machines. The others:
- 9.5 kg T series — Samsung Washing Machine Door Seal WW95T654DLE/SA WW95T754DBT
- 9.5 kg N series — Samsung Washing Machine Door Seal WW95N54F5CW/SA, WW95N54F5PW/SA WW95N64FRPWSA
- 10 kg N and T series — Samsung Washing Machine Door Seal WW10N645RBX, WW10T654DLE/SA WW10T754DBT/SA
- Older J and K series — Samsung Washing Machine Door Seal WW85K6410QX/SA, WW75K5210WW, WW75J4233GW/SA
The Samsung door seal replacement guide walks through the fit; wipe the new seal dry after the last wash and leave the door ajar.
Banging on spin: spider or bearings?
Two failures, two sounds. A cracked spider knocks on spin and leaves rust marks on light washing as the alloy sheds. Worn bearings rumble, louder with speed, and eventually weep grease under the machine. Both are often gone together, so fit the seal-and-bearing kit whenever the spider comes out.
The older H and J series use their own casting, the Samsung Washing Machine Spider Shaft WW75H5400EW/SA WW80J4413IW/SA, with a step-by-step in the WW75H5400EW banging-on-spin guide. The 10 to 12 kg machines and combos share the Samsung Washing Machine Seal Bearings Kit WD10F7S7SRP/SA, WD10F8K9ABG/SA, WD10J8420GW/SA. WD combos share the WW drum and its failures: the WD85T and WD90T spider is in the table, and the WD75M and WD85T4046 machines take the Samsung Washing Machine Spider WD75M4453JW WD85T4046CE WD85T504DBE. Honest word: any spider job is a full strip-down, three to five hours for a first-timer; the DIY section weighs it. The WW75T and WW85T parts guide covers the rest of that family.
Pumps, valves, belts and door locks
5C is a drain fault, and far more often it is the filter, a coin in the pump housing or a kinked hose than the pump; run the 5C error code guide first. 4C is the inlet side: taps, inlet screens, then the valve, in the order the 4C guide gives. A drum that stays still while the motor whirs is the belt, covered in the drive belt guide. Door locks vary by model; search your model number.
WF: the older front loaders
The WF1752, WF1804 and WF8750 series sold for years and plenty are still going. Same weak points: door seal, spider and, on some, carbon brushes worn until the drum will not turn. The spider for the earlier WF and WD drum is the Samsung Washing Machine Spider WD0804W8N WF0754W7V1 WF0854W8E1, and the WF1752 and WF1804 drum noise guide sorts which kit belongs to which drum. Seals and brushes are model-specific: search the model number, and if nothing comes up, send it through for an honest yes or no.
WA top loaders: the walking machine
The classic WA fault is the walk. The WA11M8700 spins up, the tub swings wider each rotation, and the machine shuffles off the mat. The dampers in the four suspension rods have worn. Replace all four; one new rod against three tired ones just moves the wobble. The suspension rod fitting guide shows how to hook each rod in without dropping the tub.
Overfilling or stopping short is the pressure sensor; read the Samsung pressure sensor guide before buying anything. No lock, or no spin with the lid closed, is the lid switch; never bypass it. Linty clothes are the lint filter; the lint filter guide says which fits.
Where the model sticker is and how to match a Samsung
Front loaders: open the door and look at the frame around the opening. Top loaders: the back panel, or the rear rim under the lid. A Samsung model looks like WW90T504DAW/SA or WA11M8700GV/SA. The /SA suffix marks the Australian version; if a search with it returns nothing, search without it. The series code before the slash, WW85T504 or WA11M8700, decides the part. The tail letters are mostly colour, so if your exact variant is not listed, send it through.
Type the full model number into the site search. Faded sticker? The find your model page shows where else to look, and the error codes page decodes the display. Still not sure? Send the model number through the contact page and we will check it before you order.
DIY or repairer?
Door seal: $45–90 for the part, an hour on the laundry floor. Drain pump: $100–150, half an hour with the machine on its side. Suspension rod kit: $75–100 for the four, an hour with the top panel off. All three: do it yourself.
Spider and bearings: parts in the $150–220 band, and the job is the full strip-down: top off, front off, drum out, tub split, bearings pressed out. A repairer typically charges a call-out or diagnostic fee of $100–165 before parts, then labour for the tub split, so a spider job by a tradie can run past what a mid-range machine is worth. A five-year-old machine with a cracked spider is worth the afternoon or the tradie; a twelve-year-old one needing spider, bearings and a seal probably is not.
Whatever you do, unplug at the wall before any panel comes off, fit a control board only after a proper diagnosis, and never run a top loader with the lid switch bypassed.
Frequently asked questions
Q: How do I tell spider from bearings on a Samsung front loader?
A: Lift the drum with the door open. Up-and-down play with a clunk, plus rust on the washing, is the spider; a gritty spin by hand and a rumble that grows with speed is the bearings. Do both while the tub is split.
Q: Why does my Samsung door seal keep going mouldy?
A: Warm, wet folds behind a shut door. Wipe the seal after the last wash, leave the door ajar and run an empty hot cycle monthly. Once mould has stained through the rubber, the seal is due.
Q: My Samsung shows 5C. Do I need a new drain pump?
A: Not until the drain filter is clear, the pump housing is free of coins and hair clips, and the hose is neither kinked nor pushed too far into the standpipe. Silent with all that clear, it is the pump.
Q: What does /SA mean on a Samsung model number?
A: The Australian-market version. Search with it first; if nothing comes up, drop the suffix and search the base model. The series code before the slash decides which parts are listed.
Q: Is it worth replacing the suspension rods on a Samsung top loader?
A: Yes, if the machine is otherwise healthy. The four-rod kit fits in about an hour and stops the walking and the unbalance codes. Replace all four, never one.
Find the model number on the sticker and search it on the site; the Samsung parts listed for it sit alongside the rest of our washing machine parts range. Not sure? Send the model number through the contact page and we will check before you order. Dispatched from Sydney’s Northern Beaches the day you order when it is in by 12pm Sydney time.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
