Appliance Spares
Quick answer: If your Samsung front loader is leaking from the door, growing mould in the rubber, or has a torn boot, the fix is a new door seal. A replacement Samsung door seal (DC64 series) costs $49.55 and fits a range of WD and WF front loaders. It’s a DIY job of about 45–60 minutes with no special tools — you peel off the outer retaining spring, unclip the inner clamp, fit the new seal, and refit the bands.
The part that fixes this
- Samsung Washing Machine Door Seal WD856UHSAWQ WD0754W8E/XSA, WF0854W8E/XSA, 0097
- Samsung Washing Machine Door Seal WW75T504DTW WW80T4040CE WW85T504DA
- Samsung Washing Machine Door Seal WW10N645RBX, WW10T654DLE/SA WW10T754DBT/SA 690A
Not sure it is the same on your machine? See every part listed by Samsung model number.
Last updated September 2026
Find the right door seal for your model: Samsung washing machine door seal — $49.55 · find your model
What the door seal does
The door seal — also called the door boot, gasket, or bellows — is the flexible rubber cuff between the outer door glass and the stainless drum. On a front loader it does the whole job of keeping water inside the machine during a wash and spin, while still letting the drum move and flex on its suspension. It also channels water back into the tub and carries the door lock striker.
Because it sits at the lowest point of the door opening, the boot is where detergent scum, lint and moisture collect. Over years of hot and cold cycles the rubber hardens, perishes and tears — and the folds are the number-one spot for black mould to grow.
Symptoms of a failed Samsung door seal
| Symptom | What it usually means |
|---|---|
| Water pooling on the floor below the door | Tear or perished section in the lower fold of the boot |
| Black or pink mould in the rubber folds | Trapped moisture and detergent residue — clean first, replace if perished |
| Musty smell from the drum | Mould and biofilm inside the boot fold |
| Visible splits, cracks or a flap of torn rubber | Boot has failed and must be replaced |
| Small tears at the top from coins or underwire | Foreign objects have cut the rubber |
| Door won’t seal / leak only on spin | Boot has lost its shape or the retaining band has slipped |
A leak that only appears during the fast spin, when water is thrown hard against the boot, almost always points at the seal rather than a hose or pump.
How to replace a Samsung door seal — step by step
Safety: mains voltage — always unplug at the wall before opening the cabinet.
- Unplug the machine and turn off the tap. Run a short spin first so the drum is empty, then mop out any water sitting in the boot fold.
- Open the door and find the outer retaining band. Around the front lip of the boot is a spring-tensioned band (a wire ring with a coil spring, or a clamp). Find the spring section — usually at the bottom.
- Peel off the outer band. Slip a flat-blade screwdriver under the spring and lever it out of its groove, then work the band off around the rim. On some models you first remove the lower kick panel or the front control facia to reach the clip.
- Mark the orientation. Samsung boots have a drain hole and a locating mark that must sit at the bottom. Note where the top mark and the drain point sit before you remove the old seal, or take a photo.
- Release the inner clamp. Pull the front lip of the old boot off the cabinet, then work around to the rear clamp on the outer tub — usually a spring-wire clip or a screw-tension band. Release it and lift the old seal out.
- Fit the new seal. Locate the rear lip onto the outer tub groove first, seat the clamp, and line up the drain hole and top mark. Press the rubber fully home all the way round.
- Refit the front band. Stretch the outer boot lip over the cabinet edge, sit the retaining band in its groove, then hook the spring back into place — a smooth screwdriver helps guide it round.
- Leak-test. Plug in, run a rinse-and-spin with no washing, and watch the door and floor for the full cycle before you trust it with a real load.
Which seal fits my Samsung model
This replacement boot fits the following Samsung front loaders:
- WD856UHSAWQ / WD856UHSAWQ/SA
- WD0754W8E/XSA
- WF0854W8E/XSA
- WD8704, WD8704EJA/XSA
- WD0804
- WF8750LSWXSA
- WF8750LSW1/XSA
Part reference: DC64 series. If your model isn’t listed, check the model sticker inside the door frame and run the Part Finder — Samsung uses several boot shapes across its WD and WF ranges.
Replacement cost in Australia
| Option | Cost | Notes |
|---|---|---|
| DIY — replacement seal only | $49.55 | Part only; 45–60 min of your time |
| Tradie call-out + fit | $180–$320 | Labour plus the seal |
Fitting the seal yourself saves the call-out entirely. It’s a fiddly rather than technical job — the retaining band is the only awkward part, and it goes back the way it came off.
Parts that fix this
In stock now and dispatched the same day from Sydney (order before 12pm). Not sure which one fits your model? Find your model number and match it against the fitment list on the part page before you order.
Frequently asked questions
Is this a genuine Samsung door seal?
No — it’s a quality replacement (aftermarket) door seal built to fit the listed Samsung models. It performs the same sealing job as the original boot at a lower price.
How do I know if my boot is torn or just dirty?
Wipe the folds clean and dry, then run a finger around the lower half. Mould wipes off; a tear, split or perished, crumbling section does not — and that means replacement. See our guide on removing mould from the door seal before you decide.
Can I stop the leak with sealant instead of replacing the boot?
No. Silicone won’t bond reliably to a flexing, wet rubber boot and can foul the drum. Once the rubber has split, replacement is the only lasting fix.
Do I need to remove the front panel of the machine?
On many Samsung models you can change the boot with the front on, working through the door. Some models need the lower kick panel or facia off to reach the rear clamp — check yours before you start.
Why does mould keep coming back in the seal?
Front loaders trap water in the fold after every wash. Leave the door ajar between washes, wipe the fold dry, and run a monthly hot maintenance cycle to keep it clear.
How long does a Samsung door seal last?
With good care, many years. Heat, harsh detergents and trapped moisture shorten its life — a boot that’s already perished is due for replacement regardless of age.
Related
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
