Appliance Spares
Quick answer: AEG dishwashers use the Electrolux i-code system. i10 means no water coming in (tap, hose, screen or inlet valve), i20 means the water did not drain (filter, hose or drain pump), i30 means water in the base (anti-flood), i50 is the circulation pump, i60 a heating fault, i70 the temperature sensor, iC0 to iF0 are communication and configuration faults. Clean the filters and check the tap; a code that returns after a restart names the part.
Not sure which one fits? Match your model number or check the sticker inside the door.
Every brand’s error codes in one index · Find your exact part
Last updated September 2026
AEG dishwashers share the Electrolux platform with Westinghouse and Electrolux dishwashers in Australia, so the codes are the same family: an i followed by a number, shown on the display or, on simpler models, as a count of flashes on the end-of-program light. The first digit names the system, and three codes account for nearly every fault an owner sees: i10 for filling, i20 for draining and i30 for water in the base.
This guide covers the AEG built-in, fully integrated and freestanding dishwashers sold in Australia, including the 6000 to 9000 series and the older Favorit range. For each code you get the plain meaning, the likely cause and the part or check that clears it.
AEG dishwasher error codes: quick-reference table
Codes are listed as they appear on the display. Where two generations of the platform use different codes for the same fault, both are shown. Always confirm against the manual for your exact model before ordering a part.
| Code | What it means | Most likely cause | What to do / the part |
|---|---|---|---|
| i10 | No water coming in within the time limit | Tap off, hose kinked, inlet screen blocked, inlet valve failed | Open the tap, straighten the hose, clean the screen; replace the inlet valve |
 i20 | Water not drained | Blocked filter, food in the pump impeller, kinked hose, drain pump failed | Clean the filters and impeller; straighten the hose; replace the drain pump if it hums without pumping — fit the AEG DISHWASHER WATER DRAIN PUMP 0018 |
| i30 | Anti-flood: water in the base | Leak from the door seal, hoses, sump; overfill | Unplug, empty the base, find and fix the leak |
| i40 | Pressure sensor or water level fault | Blocked pressure chamber, sensor | Clean the sump and chamber; replace the sensor |
| i50 | Circulation pump fault | Pump blocked or failed, triac | Clear glass and debris from the sump; replace the pump if it will not run |
| i60 | Water not heated | Heating element, temperature sensor, relay | Test the element; replace the element or sensor |
 i70 | Temperature sensor fault | Sensor open or short | Replace the temperature sensor — fit the AEG SensorLogic DISHWASHER DRAIN PUMP F88009M0P F88009W0P F99015IM0P 0012 |
| i80 / i90 | Board or configuration fault | Board data | Power-cycle; service if it repeats |
| iA0 | Spray arm blocked or not rotating | Item obstructing the arm, blocked holes | Clear the arm and its holes |
 iB0 | Turbidity sensor fault | Sensor dirty or failed | Clean the sensor; replace if it repeats — fit the AEG SensorLogic DISHWASHER DRAIN PUMP F88009M0P F88009W0P F99015IM0P 0012 |
| iC0 / id0 | Communication fault between boards / circulation pump speed | Cable, board, pump | Power-cycle; service if it repeats |
| iF0 | Program time or flow fault | Flow meter, slow fill | Clean the screen; replace the flow meter |
| Flashing end light | Fault shown as flash count on non-display models | One flash i10, two i20, three i30 | Match the count to the code above |
i10, i20, i30: the three that matter
Almost every AEG dishwasher fault is one of these. i10 is fixed at the tap, the hose and the little screen where the hose meets the machine. i20 is fixed at the filter in the base of the tub and the drain pump impeller behind it, where glass and food collect. i30 is water in the base and will not clear until the base is dry; unplug, tilt the machine to empty it, and look for the leak at the door seal, the hose connections and the sump.
When the part is the pump, the valve or the heater
A machine that still shows i20 with a clean filter, a clear impeller and a straight hose has a failed drain pump, which hums without moving water. A machine that still shows i10 with the tap open and a clean screen has a failed inlet valve, which is silent when the program starts. i60 with cold dishes is the flow-through heater on the circulation pump, tested for continuity and replaced as an assembly.
AEG dishwasher parts in stock in Sydney
These are the parts behind the codes above that we hold in stock and ship Australia-wide. Match the model number on your model sticker before ordering, or run it through the Part Finder and let it match for you. Every part we hold for the brand is listed on the AEG parts page, and by model on the model pages; the wider range is in the dishwasher parts store.
- AEG DISHWASHER WATER DRAIN PUMP 0018
- AEG SensorLogic DISHWASHER DRAIN PUMP F88009M0P F88009W0P F99015IM0P 0012
- AEG SensorLogic DISHWASHER DRAIN PUMP F88009M0P F88009W0P F99015IM0P 0012
- Everdure DISHWASHER DRAIN PUMP DWF125PS 0012
- AEG Dishwasher Drain Pump 0018
- AEG DISHWASHER DRAIN PUMP F77602W0P, F77602M0P, F76672M0P, F78601VI1P, 0018
- AEG ProClean DISHWASHER DRAIN PUMP F76672M0P F77602M0P 0012
- Midea Viali DISHWASHER DRAIN PUMP WQP12-9250 VGGDW60SS 0012
Is it safe to fix an error code yourself?
Most of the codes above are cleared with a filter clean, a hose check or a plug-in part swap, and those are ordinary DIY jobs: unplug the machine, photograph the wiring before you unplug anything, and never bypass a door lock or a thermal cut-out. Anything involving the sealed refrigerant circuit, gas, or a mains-side repair belongs with a licensed repairer.
Frequently asked questions
How do I reset a AEG dishwasher error code?
Switch the machine off, turn it off at the wall for one minute, then restart the program. A code that returns as soon as the machine reaches the same step is a real fault and needs the check or part in the table.
What does i20 mean on an AEG dishwasher?
The water did not drain. Clean the filters, clear the drain pump impeller and straighten the hose; replace the drain pump if it hums without moving water.
What does i10 mean?
No water came in. Open the tap, straighten the inlet hose and clean its screen; replace the inlet valve if it still will not fill.
What is i30 on an AEG dishwasher?
Water in the base has tripped the anti-flood float. Unplug, empty the base and fix the leak before restarting.
Why does my AEG dishwasher show i60 with cold dishes?
The water did not heat. Test the heating element and replace it or the temperature sensor.
Where is the model number on a AEG dishwasher?
Open the door and look at the sticker on the edge of the door or the side of the tub. The model reads like FSE83837P or F55402VI0. Use it to match parts or run it through our Part Finder.
Read the code, then fit the part
Tap, filter, base: i10, i20 and i30 in that order. The parts behind the rest are shared with Electrolux and Westinghouse and in stock. Find your AEG part now
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
