AEG Dryer Error Codes E20 to EH0: Condenser and Heat Pump

AEG Dryer Error Codes: E20 to EH0 on Condenser and Heat Pump Models (Australia 2026)

Quick answer: AEG dryers use the Electrolux dryer code system. E20 to E24 are condensate drain faults on condenser and heat pump models (container full, pump, hose), E31 to E33 the humidity sensing, E40 to E43 the door lock, E50 to E54 the motor, E61 to E64 the heater, E70 to E74 the temperature sensors, E91 to E94 the electronics and EH0 to EH2 the supply. Empty the container, clean every filter and check the drain hose; a code that returns after a restart names the part.

The parts that clear this codeGenuine and compatible parts, dispatched from Sydney (12pm cut-off)

Not sure which one fits? Match your model number or check the sticker inside the door.

Every brand’s error codes in one index · Find your exact part

Last updated September 2026

AEG dryers, like AEG washers, are built on the Electrolux platform, so their E-codes read the same way: the first digit is the system, the second the detail. E20 is the condensate system, E50 the motor, E60 the heater, E70 the sensors. On models without a full display the code shows as a C-number or as beeps and flashes, with C2 standing in for E20.

This guide covers the AEG vented, condenser and heat pump dryers sold in Australia, including the 7000, 8000 and 9000 series AbsoluteCare and SensiDry models and the older Lavatherm range. For each code you get the plain meaning, the likely cause and the part or check that clears it. Most AEG dryer codes are lint or condensate; the parts behind the rest are the drain pump, the belt and the sensors.

AEG dryer error codes: quick-reference table

Codes are listed as they appear on the display. Where two generations of the platform use different codes for the same fault, both are shown. Always confirm against the manual for your exact model before ordering a part.

Code	What it means	Most likely cause	What to do / the part
E20 / E21 / E22 (C2)	Condensate not draining: container full, pump not pumping, pump blocked	Container not emptied, lint in the condensate pump, drain hose kinked or too high	Empty the container; clean the pump chamber of lint; straighten the hose; replace the condensate pump if it hums without pumping
E23 / E24	Condensate pump circuit fault	Pump coil open, board	Replace the condensate pump
E31 / E32 / E33	Humidity (conductivity) sensor fault	Sensor bars dirty or corroded, wiring	Clean the metal sensor bars inside the drum with vinegar; check the wiring
E40 / E41 / E42 / E43	Door not closed, or door lock fault	Door open, catch worn, door switch failed	Close firmly; replace the door catch or switch
E50 / E51 / E52 / E53 / E54	Motor faults: speed, triac, tacho, relay	Motor, tacho, capacitor, belt off the pulley	Check the belt is on the pulley; replace the capacitor or motor
E61 / E62 / E63 / E64	Heater faults: not heating, too slow, relay, element	Heating element, thermostat, relay	Test the element and thermostats; replace the failed part — fit the Omega and Euromaid Dryer Heat Restore Kit OCD40WA DM4KG ED45KG (Element, Capacitor, Belt,
E70 / E71 / E72 / E73 / E74	Temperature sensor faults (front and rear sensors)	Sensor open or short, wiring	Replace the temperature sensor
E91 / E92 / E93 / E94	Electronics communication and configuration faults	Board, cable, configuration	Power off at the wall for a minute; service if it repeats
EH0 / EH1 / EH2	Supply voltage or frequency out of range	Supply, board	Check the supply; power-cycle
Drum not turning, motor runs	Belt broken	Wear	Replace the belt — fit the Westinghouse & Electrolux Dryer Belt, Idler Pulley & Rear Drum Bearing Kit — Drum Belt + P
Dries slowly, no code	Airflow restricted	Filters, heat exchanger, vent hose	Clean every filter and the heat exchanger
Container symbol with empty container	Float or level sensing in the container	Float stuck	Clean the container float channel

Not sure which part?Enter your model number and the Part Finder returns only parts confirmed to fit.

Find my part

E20 on a condenser or heat pump dryer

E20 is the AEG dryer code owners see most, and it is the condensate system. Empty the water container and push it fully home. If the code returns, lint has reached the condensate pump in the base: unplug the dryer, remove the plinth panel or the pump cover, and clear the pump chamber and the float. If an external drain hose is fitted, check it is not kinked and its outlet is under about a metre high. A pump that hums without pumping after that is replaced, and it is a plug-in part.

E31 to E33: the sensor bars

Auto-dry programs read moisture through two metal bars inside the drum near the door. Fabric softener and lint coat them and the dryer either stops early or shows an E3x code. Wipe the bars with vinegar or a fine abrasive pad until they shine. If the code stays with clean bars, the wiring to the bars has failed.

Belt, heater and sensors

A drum that will not turn while the motor runs is the belt. No heat with the drum turning is the element or a thermostat, and on this platform they are tested for continuity behind the rear panel. E70-series codes are the temperature sensors, small thermistors that fail open with age and are replaced as plug-in parts.

AEG dryer parts in stock in Sydney

These are the parts behind the codes above that we hold in stock and ship Australia-wide. Match the model number on your model sticker before ordering, or run it through the Part Finder and let it match for you. Every part we hold for the brand is listed on the AEG parts page, and by model on the model pages; the wider range is in the dryer parts store.

Is it safe to fix an error code yourself?

Most of the codes above are cleared with a filter clean, a hose check or a plug-in part swap, and those are ordinary DIY jobs: unplug the machine, photograph the wiring before you unplug anything, and never bypass a door lock or a thermal cut-out. Anything involving the sealed refrigerant circuit, gas, or a mains-side repair belongs with a licensed repairer.

Frequently asked questions

How do I reset a AEG dryer error code?

Switch the machine off, turn it off at the wall for one minute, then restart the program. A code that returns as soon as the machine reaches the same step is a real fault and needs the check or part in the table.

What does E20 mean on an AEG dryer?

The condensate is not draining. Empty the container, clean lint from the condensate pump chamber and check the drain hose; replace the pump if it hums without pumping.

What is E32 on an AEG dryer?

A humidity sensor fault. Clean the two metal sensor bars inside the drum with vinegar; if the code stays, the sensor wiring has failed.

Why does my AEG dryer run but the drum does not turn?

The belt has broken or come off. Replace the belt and check the tensioner.

What does E60 or E61 mean on an AEG dryer?

A heating fault. Test the heating element and thermostats behind the rear panel and replace the failed part.

Where is the model number on a AEG dryer?

Open the door and look at the sticker on the door rim or frame. The model reads like T8DEE845 or T7DEE832E. Use it to match parts or run it through our Part Finder.

Read the code, then fit the part

Container, pump, filters, sensor bars: most AEG dryer codes end there. The belt, element and sensors behind the rest are plug-in parts. Find your AEG part now

Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.