Appliance Spares
Quick answer: Midea dishwashers use the Midea E-code system. E1 means the machine did not fill in time (tap, hose, screen or inlet valve), E2 water not draining (filter, hose or drain pump), E3 water not heating (element or sensor), E4 water in the base (anti-flood float), E5 over-temperature, E6 and E7 the temperature sensor open or short, E8 the spray arm diverter, E9 a pump fault and Ed a communication fault. Clean the filter and check the tap; a code that returns names the part.
Not sure which one fits? Match your model number or check the sticker inside the door.
Every brand’s error codes in one index · Find your exact part
Last updated September 2026
Midea dishwashers are built by Midea, and they share Midea’s E-code system with several other badges sold in Australia. The board checks the fill, the drain, the heater, the sensor, the float in the base and the diverter that switches between spray arms, and stops with an E-code when a check fails. On models without a display the code is shown by a combination of flashing program lights.
This guide covers Midea-badged dishwashers and the same machines sold as Euromaid, Bellini, Inalto, Esatto, Omega, Hisense and several other brands in Australia. For each code you get the plain meaning, the likely cause and the part or check that clears it. The parts behind the codes are shared across all of those badges, which is why they are easy to source.
Midea dishwasher error codes: quick-reference table
Codes are listed as they appear on the display. Where two generations of the platform use different codes for the same fault, both are shown. Always confirm against the manual for your exact model before ordering a part.
| Code | What it means | Most likely cause | What to do / the part |
|---|---|---|---|
 E1 | Water not filled in time | Tap off, hose kinked, inlet screen blocked, low pressure, inlet valve failed | Open the tap fully, straighten the hose, clean the screen; replace the inlet valve if it still will not fill — fit the Midea Everdure Dishwasher Inlet Valve JHDW121FS, DWF126WC1 |
 E2 | Water not drained | Blocked filter, food in the pump impeller, kinked hose, drain pump failed | Clean the filter and impeller; straighten the hose; replace the drain pump if it hums without pumping — fit the Everdure DISHWASHER DRAIN PUMP DWF125PS 0012 |
 E3 | Water not heated to temperature | Heating element failed, temperature sensor, heater relay | Test the element for continuity; replace the element or sensor — fit the Omega, Blanco, Midea Dishwasher Heating Element |
| E4 | Water in the base: anti-flood float tripped | Leak from the door seal, hose connections or sump; overfill; foam | Unplug, tilt to empty the base, find and fix the leak |
| E5 | Over-temperature or sensor out of range | Sensor shorted, heater relay stuck on | Replace the temperature sensor; board if the heater runs constantly |
| E6 | Temperature sensor open circuit | Sensor failed or unplugged | Replace the temperature sensor |
| E7 | Temperature sensor short circuit | Sensor failed | Replace the temperature sensor |
| E8 | Spray arm diverter fault | Diverter jammed with debris or its motor failed | Clear the sump; replace the diverter |
| E9 | Pump fault, sometimes with noise from the pump area | Circulation pump blocked or failed | Clear glass from the sump; replace the pump if it will not run |
| Ed | Communication fault between the panel and the board | Cable, moisture, board | Power off at the wall for a minute; service if it repeats |
| Flashing lights, no display | Fault shown by light combination | See the manual for the pattern | Match the pattern to the code above |
E1, E2 and E4: fixed at the tap, the filter and the base
Three codes account for most Midea-platform dishwasher faults. E1 is the tap, the hose and the little screen where the hose meets the machine. E2 is the filter in the base of the tub and the drain pump impeller behind it, where glass and food collect. E4 is water in the base, and it will not clear until the base is dry: unplug, tilt the machine to empty it, then look for the leak at the door seal and the hose connections.
E3, E5, E6 and E7: the heater and its sensor
Cold dishes with E3 mean the water never reached temperature. The heater is a flow-through element on the circulation pump on most models, tested for continuity with the machine unplugged and replaced as an assembly when it reads open. E6 and E7 are the temperature sensor open or short, and E5 is the same sensor reading far too hot. All three sensor codes are one part.
Midea dishwasher parts in stock in Sydney
These are the parts behind the codes above that we hold in stock and ship Australia-wide. Match the model number on your model sticker before ordering, or run it through the Part Finder and let it match for you. Every part we hold for the brand is listed on the Midea parts page, and by model on the model pages; the wider range is in the dishwasher parts store.
- Midea Everdure Dishwasher Inlet Valve JHDW121FS, DWF126WC1
- Everdure DISHWASHER DRAIN PUMP DWF125PS 0012
- Omega, Blanco, Midea Dishwasher Heating Element
- Midea IAG Technica Delongh SMEG Whirlpool Dishwasher Inlet Valve
- STIRLING MIDEA DAMANI DISHWASHER DRAIN HOSE 2M WQP12-9240AS, DAD6002 0780
- Door Switch for Dishwasher, Microwave and Oven Universal Heavy Duty 16A 240V
- DARMANI GVA DISHWASHER DETERGENT DISPENSER DDW60S, GVADW12W 0719
- Universal Dishwasher Aquastop Hose Standard Tap Fitting Inlet Hose 1.5m 0331
Is it safe to fix an error code yourself?
Most of the codes above are cleared with a filter clean, a hose check or a plug-in part swap, and those are ordinary DIY jobs: unplug the machine, photograph the wiring before you unplug anything, and never bypass a door lock or a thermal cut-out. Anything involving the sealed refrigerant circuit, gas, or a mains-side repair belongs with a licensed repairer.
Frequently asked questions
How do I reset a Midea dishwasher error code?
Switch the machine off, turn it off at the wall for one minute, then restart the program. A code that returns as soon as the machine reaches the same step is a real fault and needs the check or part in the table.
What does E4 mean on a Midea dishwasher?
Water in the base has tripped the anti-flood float. Unplug, empty the base and find the leak before restarting.
What does E1 mean on a Midea dishwasher?
No water came in within the time limit. Open the tap, straighten the hose, clean the screen; replace the inlet valve if it still will not fill.
What does E3 mean on a Midea dishwasher?
The water did not heat. Test the heating element and replace it or the temperature sensor.
What is Ed on a Midea dishwasher?
A communication fault between the control panel and the board. Power off at the wall for a minute; if it returns it needs service.
Where is the model number on a Midea dishwasher?
Open the door and look at the sticker on the edge of the door or the side of the tub. The model reads like MDWFS or JHDW12FS. Use it to match parts or run it through our Part Finder.
Read the code, then fit the part
Tap, filter, base, then the heater. The parts behind the codes are shared across every Midea-built badge and in stock. Find your Midea part now
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
