Cheapest Heat Pump Dryer to Repair in Australia: Fisher & Paykel

Quick answer: Stirling (ALDI) and Esatto are the cheapest heat pump dryers to repair in Australia: they share a platform whose drum belt is about $12 to $35, bearing kit about $30 to $40 and door lock $35 to $45. Fisher & Paykel and Haier heat pump dryers cost more per part (belts $24 to $90, condensate pumps $90 to $100) but have the deepest parts support and the best documentation. Bosch heat pump dryers are well supported but sit at the top on price. Belts and condensate pumps are the two repairs heat pump owners actually do.

Every brand’s error codes in one index · Find your exact part

Last updated September 2026

Heat pump dryers are cheap to run and, for most of their life, cheap to own; the question is what happens when one fails. They add a sealed refrigerant circuit, which is not repairable at home, but the parts that actually fail are the same ones a conventional dryer has: the drive belt, the condensate drain pump, the door lock and the drum bearings. In our Australian Appliance Failure Index the belt is four in ten dryer repairs and the drain pump one in five.

This comparison ranks the heat pump dryers Australians buy most: Stirling (ALDI) and Esatto, which share a Midea-built platform, Fisher & Paykel and Haier, which share theirs, and Bosch. The prices are ranges from the parts we currently stock; the verdicts are about repair cost and ease, not drying performance or energy use.

Cheapest heat pump dryer to repair: the brands compared

Codes are listed as they appear on the display. Where two generations of the platform use different codes for the same fault, both are shown. Always confirm against the manual for your exact model before ordering a part.

Brand	Parts availability in Australia	Typical price of the part that fails most	Second most common repair	DIY difficulty	Verdict
Stirling (ALDI) SHPD80W and STR-HPD models	Good for the current heat pump models: belt, bearing kit, door lock, filters	Drum belt $12 to $35	Bearing kit $35 to $45; door lock $35 to $45	Moderate: the front comes off for the belt	Cheapest to repair. Shared platform, cheap parts, and the belt is the failure you will meet — fit the Haier Heat Pump Dryer Belt HDHP80AW1 HDHP80E1 HDHP90AN1 HDHP90ANB1
Esatto EHPD models	Good: belt, bearing kit, door lock, filters	Drum belt $12 to $25	Bearing kit $28 to $35; door lock $35 to $45	Moderate	Equal cheapest with Stirling; same platform, same parts
Fisher & Paykel DH and Haier HDHP models	Very good: belts, condensate pumps, sensors, door parts, capacitors	Drum belt $24 to $90	Condensate pump $90 to $100; capacitor $18 to $33	Moderate to hard: the pump and belt both need the machine open	More expensive per part, but the deepest support and every fault code documented
Bosch WTW and WQG models	Good for current series	Drum belt about $25 to $30	Door seal $120 to $134; pump and sensor assemblies at the higher end	Moderate to hard	Well supported but the most expensive parts of the group
Solt GGSHPD models	Fair	Drum belt about $12 to $25	Door lock $35 to $45	Moderate	Same Midea platform as Stirling and Esatto with a thinner listing
What fails, all brands	From the Failure Index	Drive belt: 40 per cent of dryer part purchases	Drain pump 20 per cent; bearings 7 per cent	Belt and pump are DIY; the refrigerant circuit is not	Buy on belt and condensate pump price

Not sure which part?Enter your model number and the Part Finder returns only parts confirmed to fit.

Find my part

Belts and pumps, not compressors

Owners worry about the heat pump itself, but in practice it rarely fails within the life of the machine and is not repairable at home when it does. What fails is the belt, which stretches and snaps after years of tension, and the condensate pump, which sits in the base collecting lint until it jams. Both are inexpensive on the Midea platform under Stirling, Esatto and Solt, and dearer but well supported on Fisher & Paykel, Haier and Bosch.

Why the ALDI and Esatto dryers are cheapest

Stirling and Esatto heat pump dryers are the same machine from the same factory, and their parts are standard Midea items made in volume: a belt for the price of a sandwich, a bearing kit and door lock around $30 to $40. The caveat is that some ALDI models were sold for one season, and parts for those are thinner; the current SHPD80W platform is well covered.

Fisher & Paykel, Haier and Bosch

Fisher & Paykel and Haier heat pump dryers cost more to repair per part, with belts $24 to $90 and condensate pumps $90 to $100, but they have the deepest parts range and the best documentation of any heat pump dryer sold here, so a fault is diagnosed and fixed rather than guessed at. Bosch is well supported too, at the top of the price range.

What this does not tell you

This compares the cost and ease of the repairs heat pump dryers actually need. It does not compare drying time, energy use or how often each brand fails, and it does not cover the sealed refrigerant circuit, which is a service repair on every brand.

heat pump dryer parts in stock in Sydney

These are the parts behind the codes above that we hold in stock and ship Australia-wide. Match the model number on your model sticker before ordering, or run it through the Part Finder and let it match for you. Every part we hold for the brand is listed on the parts page, and by model on the model pages; the wider range is in the heat pump dryer parts store.

Is it safe to fix an error code yourself?

Most of the codes above are cleared with a filter clean, a hose check or a plug-in part swap, and those are ordinary DIY jobs: unplug the machine, photograph the wiring before you unplug anything, and never bypass a door lock or a thermal cut-out. Anything involving the sealed refrigerant circuit, gas, or a mains-side repair belongs with a licensed repairer.

Frequently asked questions

Which heat pump dryer is cheapest to repair in Australia?

Stirling (ALDI) and Esatto, which share a Midea platform: belts $12 to $35, bearing kits and door locks around $30 to $40.

Are Fisher & Paykel heat pump dryers expensive to repair?

More expensive per part, with belts $24 to $90 and condensate pumps $90 to $100, but with the deepest parts support and documentation.

Can I repair the heat pump itself?

No. The refrigerant circuit is sealed and is a service repair on every brand. The parts that actually fail, the belt and the condensate pump, are DIY.

How were these repair costs worked out?

From the heat pump dryer parts we stock and ship in Australia: the price range of each brand’s common failure parts, how many of those parts exist for each brand, and how often each part category is bought across the year (published in our Australian Appliance Failure Index). Labour is not included; the comparison is about parts cost and how easy the repair is to do at home.

Does cheapest to repair mean most reliable?

No. This compares what it costs and how hard it is to fix the machine when it does fail. A brand can be inexpensive to repair and still fail often, or expensive to repair and rarely need it.

Are the prices here exact?

They are ranges from the parts currently listed, rounded, and they move with stock and exchange rates. Click through to the part for today’s price.

Should I repair or replace?

If the part is in the ranges here and the machine is under about ten years old, repair almost always wins: the median parts bill for a repair in Australia is around forty dollars against several hundred for a replacement plus delivery and disposal.

Read the code, then fit the part

Belt price, pump price, and whether the platform is shared: the ALDI and Esatto dryers win on all three, and Fisher & Paykel wins on support. Find your part now

Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.