Appliance Spares
Quick answer: The Fisher & Paykel WH8060P3 8 kg front loader most commonly fails on the motor controller ($148.95), which causes error codes and the drum not spinning. The drain hose ($19.95) and door interlock switch ($27.69) are also common wear parts. We stock genuine Fisher & Paykel parts and ship Australia-wide from Sydney.
Not sure which one fits? Match your model number or check the sticker inside the door.
Shop Fisher & Paykel WH8060P3 parts:
Motor Controller (WH8060P3, WH8560P3, WH9060P3) — $148.95 ·
Drain Hose (WH8060P1, WH8060J3, WH8060F1) — $19.95 ·
Door Interlock Switch — $27.69 ·
Not sure which part? Use the Part Finder
Common faults on the Fisher & Paykel WH8060P3
The WH8060P3 is a direct-drive 8 kg front loader from Fisher & Paykel’s P-series range. The motor controller — a board that drives the motor and manages wash programmes — is the single most common failure point on this model. When it begins to fail, it typically produces intermittent behaviour or error codes before stopping completely. The drain hose and door interlock switch are lower-cost wear parts that fail with age. Note that the drain hose listed below is confirmed to fit earlier P-series variants (WH8060P1, WH8060J3, WH8060F1) — if your model sticker reads WH8060P3, verify fitment against your existing hose dimensions or use the Part Finder before ordering.
| Part | Symptom | Price | Link |
|---|---|---|---|
 Motor controller | Machine won’t start, error codes displayed, drum spins intermittently or not at all | $148.95 | Buy |
 Drain hose | Leaking from the back of the machine, drain hose cracked or perished | $19.95 | Buy — verify fit first |
 Door interlock switch | Machine won’t start, door won’t register as closed, door indicator flashing | $27.69 | Buy |
Diagnosis guide — Fisher & Paykel WH8060P3
- Read any error codes on the display. The WH8060P3 logs fault codes when it detects a failure. Note the code exactly and search “Fisher Paykel WH8060P3 error code [code]” for the specific cause. Motor controller faults typically produce codes related to motor speed, communication errors, or a generic fault that clears briefly then returns.
- Check whether the drum rotates at all. Start an empty cycle and listen carefully. If the machine fills with water but the drum does not rotate — or rotates for a few seconds then stops with an error — the motor controller is the primary suspect. A seized motor bearing or worn drive belt (on belt-drive variants) can produce the same symptom, but the P-series uses a direct-drive arrangement, so the controller is the most likely cause.
- Inspect for leaks at the rear. Pull the machine forward slightly and look along the floor behind it. Water pooling at the back, particularly after the machine attempts to drain, points to the drain hose. Inspect the full length of the hose for cracks, perished sections, or a loose clamp at either end.
- Test the door interlock. Close the door firmly and listen for the click of the lock engaging. If the machine displays a door fault, or if the door closes but the machine will not begin any programme, press the door firmly again and retry. Persistent failures indicate a worn or broken interlock switch. The switch can be tested with a multimeter for continuity when the door is pressed closed.
- Find the model sticker. The model sticker is located on the inside of the door frame or on the side panel inside the door opening. Confirm the model reads WH8060P3 and note the serial number — Fisher & Paykel updated internal components through the P-series run and some parts differ between production batches.
Fitting the parts yourself
The door interlock switch and drain hose are straightforward DIY repairs. The interlock switch is mounted behind the door frame liner and reached by partially peeling back the door seal — a 30-to-45 minute job with a flat blade screwdriver and a pair of pliers. The drain hose replacement requires pulling the machine away from the wall, releasing a hose clamp at the pump outlet and one at the standpipe, and fitting the new hose — allow 20 minutes.
The motor controller is a larger undertaking. The board is typically located behind the rear panel or under the top lid depending on production variant. It involves disconnecting a wiring harness, removing the mounting screws, and seating the replacement board. A confident DIYer can complete it in around an hour. If you are not comfortable working around a live appliance’s internal wiring, a local repairer can fit any of these parts in a single visit using a part you supply.
Frequently asked questions
What are the symptoms of a failing motor controller on the WH8060P3?
The most common signs are the drum not spinning (or stopping shortly after starting), error codes on the display that clear then return, and the machine appearing to start a cycle but aborting before filling. In some cases the machine works normally for several cycles then fails intermittently before the fault becomes permanent.
Is it worth replacing the motor controller at $148.95, or should I just buy a new machine?
At $148.95 for the part, replacement is almost always worth it on a machine under eight or nine years old. A new front loader starts above $600 and installation adds further cost. If the rest of the machine is in good condition — no rust, no drum bearing noise, no seal leaks — fitting a new controller is sound economics.
Will the drain hose listed (WH8060P1, WH8060J3, WH8060F1) fit my WH8060P3?
It may, but we cannot confirm this with certainty — the listing is verified for earlier P-series variants only. Before ordering, measure your existing hose (overall length and both end diameters) and compare against the product listing, or use the Part Finder and enter WH8060P3 to see if a direct match is available. The model sticker inside your door frame will also show your production suffix.
How do I diagnose a faulty door interlock switch?
Close the door and press it firmly against the frame. If the machine still shows a door error or will not start, the interlock switch is suspect. A multimeter set to continuity mode can confirm it — disconnect the switch and test across the terminals with the door plunger pressed in; a healthy switch will show continuity, a failed one will show open circuit. The replacement switch (H0024000128A) is $27.69.
Where can I find more Fisher & Paykel WH8060P3 parts?
Use our Part Finder, enter your model number, and it will show available matches. You can also search for WH8060P3 directly or browse all Fisher & Paykel washing machine parts.
Related
- Fisher Paykel Washing Machine Motor Controller (WH8060P3, WH8560P3, WH9060P3) — $148.95
- Fisher Paykel Front Loader Drain Hose (WH8060P1, WH8060J3, WH8060F1) — $19.95
- Fisher Paykel Washing Machine Door Interlock Switch H0024000128A — $27.69
- All parts for Fisher & Paykel WH8060P3
- All Fisher & Paykel washing machine spare parts
- Part Finder — find parts by model number
Ready to fix it?
- Open the door and check the model sticker on the inner door frame — confirm the model number reads WH8060P3.
- Note any error codes displayed and match against the fault table above to identify the most likely part.
- Order from the confirmed in-stock links above, or run the Part Finder if your fault is not covered here.
- Order before 2 pm AEST on a business day for same-day dispatch from Sydney.
- If you are unsure about the drain hose fitment for the P3 variant, contact us with your serial number and we will advise before you order.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
