Appliance Spares
Quick answer: Hisense dishwasher error codes E1–E5 cover the five main fault categories — inlet (E1), drain (E2), temperature sensor (E3), base overflow (E4), and heating element (E5); most E1 and E2 faults resolve with a filter clean or hose check before any parts are needed.
Not sure which one fits? Match your model number or check the sticker inside the door.
The part that fixes this
- Hisense Dishwasher Drain pump HSCE14FS, HSCM15FS
- Hisense Dishwasher Door Lock Switch G805101 HSGA16FB HSGA16FS HSGA16FW HSGP15FB
Not sure it is the same on your machine? See every part listed by Hisense model number.
Last updated September 2026
Decode any appliance error code — instant lookup
Browse all Hisense dishwasher parts · find your model
Hisense dishwasher error codes explained
Hisense dishwashers — including the HSCE14FS, HSCM15FS, HSGA16FB, HSGA16FS, HSGA16FW, and HSGP15FB — display fault codes as E followed by a single digit on the control panel. The machine stops the wash cycle and holds the code on screen until the fault is cleared.
Codes E1 through E5 cover every major system: water inlet, drainage, temperature sensing, base overflow protection, and the heating element. In most cases the code is accurate and points you directly to the problem. The table below lists each code with its meaning and the most common causes.
Note on older Hisense models: Some earlier Hisense dishwasher models present E4 and E5 differently or use a blinking programme light rather than a code display. Always verify the fault code against the sticker on the inside of your door frame, which lists the model number.
Hisense dishwasher error codes — cause and likelihood table
| Code | Meaning | Cause | Likelihood |
|---|---|---|---|
| E1 | Water inlet fault — machine not filling in time | Tap closed or water pressure too low | Common |
| E1 | Water inlet fault | Kinked or pinched inlet hose behind machine | Occasional |
| E1 | Water inlet fault | Inlet valve solenoid failed — no water entering despite tap being open | Common |
| E2 | Drainage fault — water not pumping out | Filter blocked with food debris or grease | Very common |
| E2 | Drainage fault | Drain hose kinked or drain connection at sink blocked | Common |
| E2 | Drainage fault | Drain pump impeller jammed or pump motor failed | Moderate |
| E3 | NTC temperature sensor fault or water not heating to target | NTC sensor open-circuit or short-circuit | Moderate |
| E3 | Temperature fault | Heating element failure causing under-temperature reading | Moderate |
| E4 | Water in base — overflow / float switch triggered | Door seal leak, loose hose connection, or pump housing drip | Occasional |
| E4 | Base overflow | Excessive suds from wrong detergent type causing overflow | Occasional |
| E5 | Heating element fault — element not functioning | Heating element burned out or connection broken | Moderate |
| E5 | Heating fault | Wiring harness to element damaged or disconnected | Less common |
How to fix Hisense dishwasher E2 — drainage fault (step-by-step)
E2 is the most common Hisense dishwasher fault. Work through these steps in order — most E2 codes resolve without replacing any parts.
- Cancel the cycle and scoop out standing water. If the drum has water sitting in it, use a jug or sponge to remove it before removing the filter. This avoids spilling on the floor.
- Remove and clean the filter assembly. Lift out the lower basket. Twist the cylindrical micro-filter anti-clockwise and lift it out, then lift the flat mesh filter beneath it. Rinse both pieces under running water, scrubbing with a soft brush to remove grease and food particles. This alone resolves the majority of E2 faults.
- Check the drain hose at the back. Pull the machine forward enough to see the drain hose. It should run up to a high loop (above the cabinet base) before dropping to the sink connection. A kinked or low-lying hose allows water to siphon back and prevents proper drainage.
- Check the connection at the sink. Where the drain hose connects to the sink waste or under-sink waste tee, make sure the connection is not blocked. If a garbage disposal unit is present, confirm the knock-out plug has been removed from the inlet port.
- Inspect the drain pump. If the filter is clean and the hose is clear but E2 continues, the drain pump may be jammed or failed. The pump is located at the base of the sump. Remove any visible debris from the impeller. If the motor does not run or hums without turning, the pump needs replacement.
Replacement drain pump in stock:
Other Hisense dishwasher parts available now
- Door lock switch G805101 — HSGA16FB / FS / FW, HSGP15FB — $98.95 — if door does not latch or machine will not start
- Browse all Hisense dishwasher parts
How to reset a Hisense dishwasher after clearing a fault
Once you have resolved the underlying issue (cleaned the filter, straightened a hose, replaced a part), reset the machine by switching it off at the power point, waiting thirty seconds, and switching it back on. Select a short programme and run it to confirm the error code does not return. If it does, the fault has not been fully resolved and the next step is component testing or replacement.
For E4 (water in base), you must remove the water from the base pan before resetting. Tilt the machine forward to drain the base, or remove the kick panel and sponge out the water. The float switch will not reset while water is present.
Frequently asked questions
My Hisense dishwasher shows E2 but the filter looks clean — what else should I check?
A visually clean filter can still have grease buildup in the mesh that restricts flow. Remove the filter and hold it up to the light — if you cannot see light through the mesh, soak it in hot soapy water for ten minutes and scrub again. If the filter is genuinely clear, check the drain hose for a kink and the sink waste connection for blockage. The drain pump is the last thing to check.
Is E3 on a Hisense dishwasher the sensor or the element?
E3 specifically flags the NTC temperature sensor or the heating circuit. If the water is warming at all but not reaching the target temperature, suspect the NTC sensor. If the water stays completely cold throughout the cycle, the heating element is more likely to have failed. E5 is the dedicated heating element code, so if you see E3 alongside cold dishes, the sensor is the more likely culprit.
Where is the model sticker on a Hisense dishwasher?
Open the dishwasher door and look along the left-hand side of the door frame. The model sticker lists the model number (e.g., HSGA16FS) and serial number. Take a photo of this sticker before ordering parts — it is needed to confirm compatibility.
My Hisense dishwasher shows E4 — is it safe to use until I fix it?
No. E4 means the base of the machine contains water near electrical components. Using the machine while E4 is showing risks electrical damage and potential safety hazards. Remove the water from the base pan, identify the source of the leak, and repair it before running another cycle.
Can I fix a Hisense dishwasher E1 fault myself?
Most E1 faults can be resolved without a technician. Check the tap, inspect the hose, and confirm water pressure is adequate first. If those all check out, the inlet valve is the likely cause — replacement is a straightforward job that involves shutting off the water, disconnecting the hose, and swapping the valve. Use the part finder quiz to confirm the correct valve for your model.
Related guides
- Haier dishwasher error codes guide
- Bosch dishwasher error codes — complete guide
- Fisher & Paykel dishwasher error codes guide
Ready to fix it?
Find the correct Hisense dishwasher part using your model number from the sticker on the door frame. We stock parts for HSCE, HSCM, HSGA, and HSGP series machines and dispatch quickly across Australia.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
