Appliance Spares
Quick answer: Only the 8kg Esatto dryers — the EHPD80 heat pump and ECD80W condenser — show error codes on a display, and the documented list is short: E32 (humidity sensor), E33 (temperature sensor), E82 (control-board communication, EHPD80 only) and FUL (water container full, or the pump that empties it has failed). The 7kg EHPD7 and ECD7 have no display at all — they signal faults by lighting the Child Lock LED together with a delay-time LED — and the vented EVD7 flashes its dryness-level lights instead. First thing to try for almost any of them: empty the tank, clean the lint filter, then switch off at the wall for 15 minutes and restart.
Decode any appliance error code — instant lookup
Which Esatto dryers show error codes
Esatto is an Australian house brand, and its dryers fall into three families that report faults in three different ways:
- 8kg display models — EHPD80 (heat pump) and ECD80W (condenser). The digital time display doubles as the error readout, so these are the only Esatto dryers that show real alphanumeric codes: E32, E33, FUL and — on the EHPD80 only — E82. How the heat pump technology itself fails is covered in our general heat pump dryer error codes guide.
- 7kg knob models — EHPD7 (heat pump) and ECD7 (condenser). No display. These share one manual and one trick: a fault lights the Child Lock LED together with a delay-time LED (3h, 6h or 9h). If you don’t know the combination, the machine just looks locked — the table below decodes it.
- 7kg vented — EVD7. No display either. The current manual names E1, E2 and E3, but the machine shows them by flashing the dryness-level lights. Older EVD7 units predate even that: no codes at all, just a manual reset button on the rear panel (covered below).
Codes that are not in the table below — E30, E5-anything, F-codes, door codes — are not documented for any Esatto dryer. If you’re seeing something else, note exactly which lights are lit and check your manual for your exact model, or run it through our appliance error code decoder to rule out a mix-up with another machine in the laundry.
Esatto dryer error codes at a glance
| Code / lights | Models | What it means | What to check first |
|---|---|---|---|
| E32 | EHPD80, ECD80W | Humidity (dryness) sensor error | Power off 15 minutes; clean the lint filters; returning code = book a technician |
| E33 | EHPD80, ECD80W | Temperature sensor error | Power off 15 minutes, restart once; persistent = technician |
| E82 | EHPD80 only | Control boards not communicating | Power off at the wall 15 minutes; returns = technician |
| FUL | EHPD80, ECD80W | Water container full — or the drain pump / level sensor can’t clear it | Empty the tank and restart; FUL with an empty tank points at the pump — see below |
| Child Lock LED + 9h LED | EHPD7, ECD7 | Temperature sensor failure | Power off 15 minutes; persistent = technician |
| Child Lock LED + 6h LED | EHPD7, ECD7 | Humidity sensor failure | Clean the lint filter, power-cycle; persistent = technician |
| Child Lock LED + 3h LED | ECD7 only | Heater failure | Power-cycle once; persistent = technician |
| Full LED stays on | EHPD7, ECD7 | Container full, or pump / level sensor failed | Empty the container; still lit = technician |
| E1 — Light dryness LED flashes | EVD7 | Dryer internally too hot | Unplug, reduce the load, clean the lint filter, check ventilation |
| E2 — Light + Standard LEDs flash | EVD7 | Temperature sensor error | Unplug 15 minutes, retry; persistent = technician |
| E3 — Extra dryness LED flashes | EVD7 | Temperature sensor error | Same 15-minute unplug reset; persistent = technician |
FUL: the one code you’ll fix yourself most often
A heat pump or condenser dryer doesn’t vent moisture — it collects it. FUL simply means the water container is full, and the dryer pauses until it’s emptied. Switch off at the wall before anything beyond the basics.
- Slide the container out, empty it, and push it back until it seats fully. A container that isn’t home reads as full.
- If your dryer is plumbed to a drain, check the hose isn’t kinked, crushed or routed higher than the machine.
- Restart the cycle. One-off FUL after a big towel load is normal in the middle of a Sydney winter — that’s a lot of water.
FUL that stays on with an empty, correctly seated tank is the manual’s other meaning: the water pump or its level sensor has failed and the machine can no longer move condensate up to the container. That repair runs the same way on most tank dryers — our drain pump replacement guide shows what’s involved — but on the Esatto platform the pump isn’t sold as a listed user-fit part, so it’s one for a technician.
E32 and E33: sensor errors on the 8kg models
E32 is the humidity sensor, E33 the temperature sensor. Both sensors feed the auto-dry programs, so when one drifts out of range the dryer stops rather than guessing. The realistic DIY end of it:
- Switch off at the power point and leave the dryer 15 minutes, then run a short cycle. A one-off glitch clears here.
- Clean the lint filters properly — a film of lint or fabric-softener residue over the sensor area confuses dryness sensing.
- If the code returns, stop there. On these models sensor replacement is a service job, and the manual routes both codes straight to the support line.
E82 on the EHPD80 is the same story one level up: the control boards have stopped talking to each other. Power-cycle once; if it comes back, it’s a technician visit, not a part you swap at home.
EHPD7 and ECD7: reading the LED combinations
The 7kg pair confuses more owners than any code, because a fault looks like the child lock has jammed on. The Child Lock LED lighting together with a delay-time LED is the fault display: 9h means the temperature sensor, 6h the humidity sensor, and 3h (on the ECD7 condenser only) the heater. All three route to service — but before you book anyone, do the free checks: clean the lint filter, make sure the room isn’t freezing cold or shut up airtight, switch off at the wall for 15 minutes and try again. A surprising number of sensor trips on these machines are really airflow problems wearing a sensor’s name.
What you can fix yourself on this platform are the mechanical wear items that don’t throw codes at all. A drum that has stopped turning while the motor hums is classic belt failure — we stock the EHPD7 drum belt and the EHPD80 drum belt, and the door lock and door hook fit the whole EHPD7 / ECD7 / EHPD80 / ECD80W family. A dryer that won’t start and won’t light anything is far more often a door-lock problem than an electronics one — our Esatto door won’t lock guide walks through it.
E1 on the EVD7: overheating, and the hidden reset button on older units
On the vented EVD7, E1 (Light dryness LED flashing) means the dryer got too hot inside. The manual’s own causes are the honest ones: an overloaded drum, a blocked lint filter, or blocked ventilation. Unplug the dryer, open the door and let it cool, halve the load, clean the filter, and make sure the exhaust path actually goes somewhere — a vented dryer in a closed laundry cupboard will cook itself. If drying times were already stretching out before the fault, run through our dryer takes too long to dry checks; a worn EVD7 drum belt or a cracked fan blade that’s stopped moving air are the usual mechanical suspects, and both are DIY-level parts.
Older EVD7 units have no error codes at all. If an older unit simply stops heating, the earlier manual documents a safety reset button on the backboard: let the dryer cool for ten minutes, then press the white button on the rear until it clicks, and it will heat again. The commonest trigger is a blocked lint filter, so clean it before you reset — otherwise you’ll be around the back of the machine again next week. E2 and E3 (temperature sensor) get the standard treatment: unplug for 15 minutes, retry, and book service if they return.
Lights that aren’t faults
- FUL with a genuinely full tank — a chore reminder, not a fault. Empty it and carry on.
- Filter icon or Clean Filters warning (8kg models) — routine lint-filter reminder.
- Filter and Full LEDs at the end of a cycle (EHPD7/ECD7) — the manual has these light up after every cycle as maintenance reminders. Nothing is wrong.
- Child Lock LED on its own — the child lock is engaged. It’s only a fault display when a delay-time LED lights with it.
Find the exact part for your model
Every fix above depends on your exact model code — EHPD80, ECD80W, EHPD7, ECD7 or EVD7 — and it’s on the model sticker, usually around the door opening or on the rear panel. Our find your model page shows where to look, and if the sticker is long gone our guide to identifying an old dryer without a model sticker walks through the detective work. Model code in hand, the Part Finder quiz matches the right part in under a minute, the EHPD80 parts guide covers that model’s common fixes in depth, or browse the full dryer parts range.
FAQ
Why is the Child Lock light on together with a time light on my Esatto dryer?
That combination is how the 7kg EHPD7 and ECD7 display faults — they have no screen. Child Lock plus 9h is the temperature sensor, plus 6h the humidity sensor, plus 3h (ECD7 only) the heater. Power off at the wall for 15 minutes and clean the lint filter first; if the combination returns, it’s a service call.
My Esatto dryer shows FUL but the water container is empty. What now?
Reseat the container firmly — a container that isn’t fully home reads as full. If FUL persists with an empty, seated tank, the manual’s second meaning applies: the water pump or its level sensor has failed, and the dryer can’t confirm it has moved the condensate. That one is a technician repair on this platform.
Is there a full list of Esatto codes like E30, E50 or F-codes?
No. The documented set for Esatto dryers is exactly what’s in the table above: E32, E33, E82 and FUL on the 8kg display models, LED combinations on the 7kg pair, and E1 to E3 on the current EVD7. Anything else on the display isn’t in the manuals — the manual’s own instruction for an undocumented prompt is to stop and call the service line.
My older Esatto EVD7 stopped heating and shows nothing at all. Is it dead?
Probably not. Older EVD7 vented dryers have a manual thermal cutout with a reset button on the rear panel. Unplug the dryer, let it cool ten minutes, press the white button on the backboard until it clicks, and clean the lint filter before the next load — a blocked filter is the usual reason it tripped.
Can I keep drying with a sensor code showing?
Don’t. E32/E33-class faults disable the auto-dry sensing the machine relies on to stop heating at the right time. Run the checks above; if the code comes back, leave it off at the wall and book a technician rather than running timed cycles around a fault.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
