Asko Dryer Error Codes — Complete Australian Guide (2026)

Quick answer: Every current Asko dryer sold in Australia has a display that shows error codes, but the list depends on the line: the Classic T208H and Logic T408HD share a short table (E-0 to E-5), while the Style T608HX shows E0 through E9 plus plain-text messages. The only code you can clear yourself is E-4 — clean the filters. Everything else — control unit, thermistor, pump, relay — is the machine asking for an Asko service technician. Before believing any code: clean every filter, then switch off at the wall for 15 minutes and restart.

Last updated September 2026

Decode any appliance error code — instant lookup

Which Asko dryers show error codes

Asko’s model letters tell you the machine type before you look anything up: V is vented, C is condenser and H is heat pump. So the T208H — despite being the entry Classic line — is a heat pump dryer, as are the Logic T408HD and Style T608HX. All three families have a display unit, and the manual is explicit: if a failure occurs while a program is running, the relevant error is indicated on the display.

• Classic (T208H) and Logic (T408HD) — one shared fault table, written E-0 to E-5.
• Style (T608HX) — a longer table, E0 to E9, plus text prompts in plain English (“Clean door filter”, “Cycle was interrupted by power failure. Please resume.”, and on steam models “Steam tank is empty. Please fill water.”).

The honest headline for Asko owners: these are premium, sensor-dense machines, and Asko’s own documentation routes nearly every code to its service network rather than to DIY. Where a code has a genuine at-home fix, it’s below; where it doesn’t, we say so rather than inventing one. General heat pump behaviour — why these machines stop heating or start leaving loads damp — is covered in our heat pump dryer error codes guide.

Asko dryer error codes at a glance

E-4: the one code that’s yours to fix

E-4 (E4 on the Style line) means restricted airflow, and on a heat pump dryer lint is almost always the culprit. Switch off at the power point first.

1. Open the door and clean the door filter properly — both layers, not just the top mesh.
2. Open the lower service flap and clean the base filter in front of the heat exchanger. This is the one people forget, and it’s usually the one that trips E-4.
3. Wipe lint from around the filter seats so it doesn’t get drawn straight back in.
4. Restart. If E-4 comes back with genuinely clean filters, the airflow path deeper in the machine needs a technician — don’t keep clearing and re-running it.

Mid-winter, with the dryer running daily, it’s worth cleaning both filters weekly — a part-blocked filter also shows up as longer cycles and damp corners on big loads long before it earns a code. Our dryer takes too long to dry guide runs the same checks in symptom order.

E-3: condensate pump problems

Heat pump dryers collect water and pump it up to the tank; E-3 means that pump has failed or can’t move water. The at-home end of it is short: empty and reseat the water container, and if the dryer is plumbed to a drain, check the hose for kinks and make sure it isn’t routed above the machine’s rated height. If E-3 returns after that, the pump itself is the likely fault — the job is the same shape as on other tank dryers (our drain pump replacement guide shows what’s involved), but Asko routes this repair through its service network, and the sealed heat-pump circuit around it is not a place for exploratory DIY.

Faults that never show a code: the drum belt

Asko’s table covers electronics and sensors, but the most Australian of dryer failures — the drum stops turning while the motor still hums — usually shows no code at all, because nothing electronic has failed. That’s the drive belt, and it is a stocked, DIY-level part: the Asko dryer drum drive belt fits the T208H, T408HD and T608HX. Our dryer belt replacement guide covers the general method, and the heat pump dryer not tumbling guide covers the belt-vs-motor diagnosis on this style of machine.

Messages that aren’t faults

• “Clean door filter” (Style line) — routine reminder, not an error.
• “Cycle was interrupted by power failure. Please resume.” — press start and the program continues; nothing is broken.
• “Steam tank is empty. Please fill water.” — steam models pause until the tank is refilled.

Find the exact part for your model

Asko model codes matter — T208H, T408HD and T608HX take different panels and boards even where they share a belt — and the full code is on the model sticker, usually around the door opening or on the rear panel. The find your model page shows where to look for every brand, and with the code in hand the Part Finder quiz matches the right part in under a minute, or browse the dryer parts range.

Related guides: dryer spare parts guide

FAQ

Why does almost every Asko dryer code say to call service?

Because that’s genuinely what the manuals specify. Asko documents E-0 through E9 for its Australian dryers, and apart from E-4 (clean the filters) every code routes to its service network — these are sensor-dense machines with a sealed heat-pump circuit, and Asko doesn’t publish board-level DIY procedures. The honest play at home: clean filters, power-cycle once, and if the code returns book the technician rather than parts-cannon guessing.

Is the Asko T208H a vented dryer?

No — the H is the giveaway. Asko’s suffix letters are V for vented, C for condenser and H for heat pump, so the T208H is the heat pump Classic. The vented Classic is the T208V, which shares the same failure-display approach on its own display unit.

What does E-5 mean on an Asko dryer?

Maximum program time: the dryer ran out of allowed time before reaching target dryness, on the Classic and Logic lines. It’s usually an airflow or load story — clean both filters, dry smaller loads, and check the room isn’t too cold or airtight. If it repeats with clean filters and sensible loads, have a technician check the sensing and heat-pump side.

My Asko dryer’s drum won’t turn but there’s no error code. What is it?

Almost always the drive belt — a snapped belt shows no code because the motor and electronics are fine. Listen for the motor humming while the drum stays still, and spin the drum by hand: little resistance points at the belt. It’s a stocked part for the T208H, T408HD and T608HX, and a repair a confident DIYer can do at the kitchen-bench level.

Can I clear an Asko error code by resetting the dryer?

A power-cycle — off at the wall, 15 minutes, back on — clears one-off glitches, and it’s always worth one attempt. But Asko’s codes exist to protect the machine: if the same code returns after a reset and a filter clean, it’s reporting a real fault, and running it repeatedly around the code risks turning a sensor fault into a bigger repair.