Appliance Spares
Quick answer: A perished or torn door seal on a Hisense HWFY7514 front loader leaks, breeds mould and throws balance faults. The fix is the genuine Hisense HWFY7514 door seal (no spray hole), $71.95, with same-day dispatch from our Sydney warehouse. Most people fit it themselves in under an hour.
The part that fixes this
- Genuine Hisense Washing Machine Door Seal HWFY7514 (No Spray Hole)
- Hisense Front Load Washing Machine Door Seal HWFS8514E HWFS1015E
- Hisense Washing Machine Door Seal HWFY8514 HWFY9514 HWFY1014
Not sure it is the same on your machine? See every part listed by Hisense model number.
Last updated September 2026
The rubber door seal (also called the door boot or bellows) is the part that fails most often on any front loader, and Hisense is no different. It flexes thousands of times a year, traps grit and detergent in its folds, and sooner or later it splits, goes hard or grows mould you can’t scrub out. On the HWFY7514 a failed seal usually shows as water pooling under the door mid-wash, or a musty smell that comes straight back a day after you’ve cleaned it. It’s a DIY job for most people, and the correct genuine part is in stock.
How do I know it’s the door seal that’s failed?
Work through these before you order. The seal is the likely culprit when:
- Water leaks from the bottom of the door on fill or spin, usually a thin trickle that pools at the front.
- You can see a split, crack or tear in the rubber. Check the lower third of the seal (the 6 o’clock position), where water and grit collect.
- There’s mould or a musty smell sitting deep in the folds that comes back within a day of cleaning.
- The rubber has gone hard, brittle or sticky. Perished rubber stops compressing against the glass, so it can’t hold water.
- Socks, coins or an underwire have worked through a gap, and you can feel the rubber has stretched or torn around the opening.
If the water is coming from the detergent drawer, the pump filter at the bottom front, or a hose connection instead, the seal isn’t your problem. Those are separate fixes. There’s a full leak walk-through in our companion guide on a Hisense front loader leaking from the door. But if the rubber itself is split, perished or mouldy past cleaning, the seal is the part to replace.
Which door seal fits my Hisense HWFY7514?
The correct part is the genuine Hisense washing machine door seal for the HWFY7514 (no spray hole). The HWFY7514 is the 7.5kg PureJet front loader, and it takes the no-spray-hole seal. This catches a lot of people out: some Hisense front-load seals have a moulded spray hole (a small nozzle port for the recirculation jet) and some don’t. You have to match spray-hole against no-spray-hole. A seal with the wrong configuration won’t seat or seal properly even if the diameter looks identical. The HWFY7514 is no spray hole.
If you’ve got a different Hisense front loader, we stock the matching genuine seals too. The table below covers the range.
| Part number | Fits these models | Genuine/Compatible | Price | Buy |
|---|---|---|---|---|
 HWFY7514 door seal (NO SPRAY HOLE) | Hisense HWFY7514 (7.5kg PureJet front loader) | Genuine | $71.95 | GENUINE HISENSE WASHING MACHINE DOOR SEAL HWFY7514 (NO SPRAY HOLE) $71.95 |
| HWFS8514E / HWFS1015E seal | Hisense HWFS8514E (8.5kg), HWFS1015E (10kg) | Genuine | $71.95 | Washing machine parts |
| HWF3S8514 / HWFS7514S seal | Hisense HWF3S8514 (8.5kg), HWFS7514S (7.5kg Series 3) | Genuine | $71.95 | Washing machine parts |
| HWFS1015AB Series 7 seal | Hisense HWFS1015AB (10kg Series 7) | Genuine | $71.95 | Washing machine parts |
| HWFE7510 seal | Hisense HWFE7510 | Genuine | $54.55 | Washing machine parts |
| WFEA6010 / WFU6012 / HWFR6510 seal | Hisense WFEA6010, WFU6012, HWFR6510 | Genuine | $64.55 | Washing machine parts |
A few cross-references worth knowing. The HWFS8514E and HWFS1015E share a seal ($71.95), and so do the HWF3S8514 and HWFS7514S ($71.95). The HWFS1015AB Series 7 has its own genuine seal ($71.95). The older and smaller models are different: the HWFE7510 takes a $54.55 seal, and the WFEA6010, WFU6012 and HWFR6510 share a $64.55 seal. For the HWFY7514 itself, the one check that matters is the spray hole. Order the no-spray-hole seal.
Not sure which model you’ve got? The model number is on a sticker on the back panel, or inside the door rim. Or run our part finder quiz and we’ll confirm the exact match.
How to replace the Hisense door seal, step by step
Time: 45 to 60 minutes for a first-timer. Difficulty: moderate DIY. Tools: flat-blade screwdriver, pliers, a towel, and a flathead or trim tool to ease the retaining spring out. Nothing special.
Safety first: switch the machine off at the wall and unplug it. Turn off the water taps at the back, and keep a towel and a shallow tray handy. There’s always residual water sitting in the bellows and sump.
- Power off at the wall, unplug, and close the inlet taps. Pull the machine forward so you can get at the front.
- Open the door and find the outer spring clamp. Around the front edge of the seal, where it meets the machine’s outer rim, there’s a retaining band held by a spring (sometimes a screwed clamp instead). Find the spring’s tail or the clamp screw.
- Slip a flat-blade screwdriver under the spring and ease it out of its groove, working around until the band lifts free. Tuck the rubber lip inwards, away from the front panel.
- Note the orientation before you remove anything. Look for the drain holes in the bottom of the seal and any locating mark or arrow (usually near the top). The new no-spray-hole seal has to go back the same way up, drain holes at the bottom (6 o’clock).
- Release the inner clamp. Reach inside and find the second retaining band, where the seal grips the drum lip. Release its spring the same way. Some models need the front panel or door interlock off first for clear access. If yours does, take out the few retaining screws and set the panel aside.
- Peel the old seal off the drum lip and lift it out. Expect trapped water and gunk. Wipe the lip clean so the new seal seats properly.
- Fit the new seal, inner side first. Push it onto the tub lip, seating it evenly all the way round with the drain holes at the bottom. Work in opposite quarters (top, bottom, then the sides) so it sits flat with no twists.
- Refit the inner spring clamp. Stretch the band back into its groove and seat the spring evenly. Run a finger right round to check the rubber is fully home with no kinks.
- Fit the outer lip and clamp. Pull the front lip of the seal over the outer rim, then refit the outer spring band into its groove. This is the band that keeps water inside, so get it evenly tensioned.
- Refit any panel you took off, plug in, open the taps, and run a short rinse and spin (or a quick cottons cycle) on an empty machine. Watch the door edge for leaks and check the floor underneath stays dry.
If you spot a drip, stop the cycle and re-seat the lip where the water’s appearing. A small kink in the rubber is almost always the cause.
Parts that fix this
In stock now and dispatched the same day from Sydney (order before 12pm). Not sure which one fits your model? Find your model number and match it against the fitment list on the part page before you order.
Frequently asked questions
How much is a Hisense HWFY7514 door seal?
The genuine HWFY7514 door seal (no spray hole) is $71.95, with same-day dispatch from our Sydney warehouse on orders placed before cut-off.
Is this a genuine Hisense part?
Yes. It’s the genuine Hisense washing machine door seal HWFY7514 (no spray hole), not a generic copy. We stock genuine seals across the Hisense front-load range.
Will this seal fit my Hisense model?
It’s made for the HWFY7514, which takes the no-spray-hole seal. Match spray-hole against no-spray-hole carefully, because a wrong-configuration seal won’t seal properly. Other models take different genuine seals: the HWFS8514E and HWFS1015E share a $71.95 seal, the HWF3S8514 and HWFS7514S share a $71.95 seal, the HWFS1015AB Series 7 has its own $71.95 seal, the HWFE7510 takes a $54.55 seal, and the WFEA6010, WFU6012 and HWFR6510 share a $64.55 seal. Check your model sticker or use the part finder quiz.
How long does delivery take?
We dispatch same-day from our Sydney warehouse on in-stock orders placed before cut-off, so most Australian metro customers have the seal within a couple of business days.
Can I replace the door seal myself?
Yes. It’s a moderate DIY job most people finish in 45 to 60 minutes with basic hand tools. Always unplug the machine and turn off the water taps first. Follow the steps above, keeping the new seal’s drain holes at the bottom and both spring clamps evenly seated.
My Hisense is leaking but the seal looks fine. What else could it be?
Leaks also come from the detergent drawer, the pump filter at the bottom front, or a loose hose connection. Work through our companion guide on a Hisense front loader leaking from the door before you replace the seal.
Not sure which Hisense boot you need?
Hisense used more than one door seal across its Australian range. If your machine is not an HWFY7514, our guide to reading the part number off the old seal shows how to tell the two variants apart before you order.
