Appliance Spares
Quick answer: If your Haier vented dryer stops part-way through a cycle or the timer dial won’t advance, the mechanical timer has usually worn out or seized. On the HDY-M40 / HDY60M it’s a $46.95 part and about a 30–45 minute DIY job. A new dryer is several hundred dollars, so swapping the timer is the clear-cut fix.
Haier clothes dryer timer — HDY-M40 · find your model
Why the cycle won’t advance
These Haier dryers use a mechanical timer — a little clockwork-and-contacts motor that you wind round to set the time. It drives the cycle and switches the heater and motor on and off. When the timer motor seizes or its contacts burn, the dial stalls and the dryer stops mid-cycle, or won’t start at all.
| Cause | How to spot it |
|---|---|
| Seized / failed timer motor | Dial won’t advance, cycle stalls at the same point every time |
| Burnt timer contacts | Dryer stops mid-cycle, sometimes won’t power the heater or motor |
| Tripped thermal cut-out | Stops after overheating — check for a blocked vent or lint first |
| Faulty door switch | Stops if the door is nudged — rule this out before the timer |
| Worn dial knob / spindle | Knob spins but doesn’t turn the timer shaft |
Confirm it’s the timer
- Clear the lint filter and check the vent isn’t blocked, then run a cycle — overheating from poor airflow can stop a dryer and look like a timer fault.
- Watch the dial. If the dryer runs but the dial never advances, or always dies at the same spot, the timer is the prime suspect.
- Check the door switch by pressing the door firmly closed while it runs — if it only stops when the door moves, that’s the door switch, not the timer.
- Unplug and pull the knob — make sure the spindle turns the timer, not just the knob spinning loose. A seized or electrically dead timer needs replacing.
Rule out the easy stuff: a blocked vent and a worn door switch both mimic a timer fault. Clean the airflow and check the door switch before you condemn the timer.
Order the right timer for your Haier
Match the model on your sticker — this timer suits the HDY-M40 family:
This is a hard-to-find Haier timer most parts counters can’t supply. Not sure of your model? Run your model number through the Part Finder — model in, exact-fit timer out.
Replace the timer (about 30–45 minutes)
- Unplug at the wall before touching anything — the timer is mains wired.
- Pull off the control knob and remove the screws holding the control panel or fascia.
- Photograph the wiring on the back of the timer carefully — there are several terminals and order matters.
- Transfer the leads one at a time from the old timer to the new one, or unplug the loom connector if fitted, matching the photo exactly.
- Mount the new timer, refit the panel and push the knob back on the spindle.
- Restore power and wind the dial to a short setting — confirm the dryer runs and the dial advances.
- Run a full short cycle to check it completes and shuts off on time.
Repair cost summary (Australia 2026)
| Path | Cost | Time |
|---|---|---|
| DIY: replacement timer | $46.95 | 30–45 minutes |
| Professional repair: part + call-out | $210–$320 | 1-hour booking |
| Replacement Haier dryer | $400–$700 | — |
Frequently asked questions
My Haier dryer stops mid-cycle — is it the timer?
Often, especially if it always dies at the same point or the dial won’t advance. Rule out a blocked vent and a faulty door switch first, then replace the timer.
The knob turns but nothing happens — timer or knob?
Check whether the spindle turns with the knob. If the knob spins free, it may just be the knob; if the spindle turns but the dryer is dead, it’s the timer.
Is wiring the new timer hard?
It’s straightforward if you photograph the terminals first and move the leads one at a time. Take your time and match the picture.
Could a blocked vent cause this?
Yes — overheating from poor airflow trips a cut-out and stops the dryer. Always clean the filter and vent before blaming the timer.
Where do I get Haier dryer parts?
We stock the Haier dryer range. See our Haier dryer parts.
Related
- Haier dryer parts — full range
- Hard-to-find appliance brand parts — full index
- All dryer timers in stock
Ready to fix it?
- Run your model number through the Oz Appliance Spares Part Finder — model in, exact-fit timer out.
- Browse 3,000+ parts in stock
- Order before 12pm Sydney time → ships same day from our Sydney Northern Beaches warehouse, Australia-wide.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
