Haier Dryer Error Codes — Complete Australian Guide (2026)

Quick answer: Haier dryer error codes only appear on the digital condenser (HDC80E1) and heat pump (HDHP80A1, HDHP80E1) models sold in Australia — vented HDV dryers have no code table and signal a fault with continuous beeping and panel lights instead. The two codes owners search most are F2 (condensate drain pump error, usually a full water tank or blocked drain path) and F4 (laundry temperature not rising, meaning no heat). Before anything else, empty the water tank, clean the lint and condenser filters, then switch the dryer off at the wall for about a minute and retry — if the code returns, the sections below tell you which part fixes it.

Last updated September 2026

Decode any appliance error code — instant lookup

Which Haier dryers show error codes

Haier only publishes a fault-code table for two families of its Australian standalone dryers: the HDC80E1 condenser dryer and the HDHP80A1 / HDHP80E1 heat pump dryers. These digital models show F-series codes (F2, F31, F32, F33, F4, F5) on the display, alongside tank and filter indicators that are reminders rather than faults. Check your manual for your exact model, because the same code can point at different hardware depending on whether the machine is a condenser or a heat pump.

One honest note: nearly all of Haier’s F-codes are technician-diagnosed faults. What a homeowner can genuinely resolve are the tank, filter and drain-path problems — which are also the most common triggers, and clear a large share of F2 and F4 displays without a single tool. If you own a heat pump model, our general heat pump dryer error codes guide explains how this dryer type fails across all brands.

Haier vented dryers (HDV models): beeps and lights, not codes

Haier’s standalone vented dryers — the HDV40A1, HDV60A1, HDV70E1 and their AWW1 variants — have no published error-code table at all. When one of these detects a fault it beeps continuously, turns the panel lights off and shows a generic number on models with a display; basic models simply flash a light. Haier’s instruction is to record what you see and call service — that number isn’t a code you can look up.

What you can do is run the symptom checks that cover the common vented-dryer failures:

1. Switch the dryer off at the wall before you touch anything, then wait a minute and restart — a one-off glitch often clears.
2. Clean the lint filter thoroughly and check the exhaust path isn’t blocked or kinked; restricted airflow is the number-one cause of a vented Haier overheating and cutting out.
3. If the dryer runs but clothes stay damp or it cuts out mid-cycle when hot, the exhaust temperature sensor is the usual suspect. We stock a Haier dryer exhaust sensor for the HDV40A1, HDV50E1, HDV60A1 and HDV60E1 and a separate exhaust sensor for the HDV70E1 and related models.
4. If the motor hums but the drum doesn’t turn, or you hear squealing, the Haier dryer drive belt has stretched or snapped.

Not sure which sensor or belt suits your machine? Run your model number through the Part Finder quiz, and if you own the older HDY-M40 there’s a dedicated Haier HDY-M40 dryer parts page covering that model.

Haier dryer error codes at a glance

Code	What it means	Most likely cause	The fix / part
F2	Drain (condensate) pump error — HDC80E1, HDHP80A1, HDHP80E1	Full tank, kinked or too-high drain hose, lint-clogged pump area, or a jammed pump	Empty the tank and clear the drain path; if it returns, fit a Haier heat pump dryer drain pump
F4	Laundry temperature not rising (no heat) — all three digital models; on heat pumps can indicate a refrigerant leak	Condenser: heater element or tripped thermal cut-out. Heat pump: sealed-system fault. Both: badly blocked filters	Clean both filters and retry; condenser models may need the condenser dryer heater; heat pump models need a technician
F5	Communication failure between main board and display board — all three digital models	Loose or damaged board harness, faulty board	Power off at the wall for a minute; if it returns, technician — boards aren’t user-serviceable
F31	NTC1 temperature sensor (near the lint filter) open or short — HDC80E1 only	Faulty thermistor or sensor wiring	Power-cycle; persistent = technician sensor replacement
F32	Temperature sensor open/short — NTC2 near the heater on the HDC80E1; the condenser/heat-exchanger sensor on heat pump models	Faulty thermistor or sensor wiring	Power-cycle; persistent = technician
F33	Condenser/heat-exchanger thermal sensor open or short — heat pump models only (HDHP80A1, HDHP80E1)	Faulty condenser thermal sensor or wiring	Power-cycle; persistent = technician

Worth knowing: belts and drum bearings never throw an error code on any Haier dryer — they’re diagnosed by symptom (squealing, rumbling, a drum that won’t turn), and we stock the drive belt, Haier dryer drum bearing and front drum guide bearings for exactly those jobs.

F2: drain pump error

F2 means the dryer can’t move condensate water where it needs to go. It’s the most common Haier code and the one most often fixed without a part. Switch the dryer off at the wall before you start.

1. Empty the water tank, even if it doesn’t look full.
2. If you’ve plumbed in the drain hose, check it isn’t kinked, pinched behind the machine or raised more than about a metre — the little pump can’t push water higher than that.
3. Open the lower panel and clean the condenser/pump filter area; a mat of wet lint around the pump is a classic F2 trigger.
4. Switch off at the wall for about a minute, then retry a cycle.

If F2 returns after all four checks, the condensate pump itself has jammed or failed — occasionally it’s pump wiring or the board, but the pump is the usual culprit. We stock the genuine Haier heat pump dryer drain pump for the HDHP80E1; for other models, confirm the right pump through the Part Finder quiz.

F4: dryer not heating

F4 means the laundry temperature isn’t rising — tumbling, but no heat. What it points to depends entirely on which dryer you own. Turn the dryer off at the wall before opening anything.

1. Clean the lint filter and the condenser filter and make sure nothing is choking airflow — a severely restricted airflow path can hold temperatures down far enough to trip F4.
2. Re-run a normal heated cycle with a sensible load; overloading masks heat and confuses the sensors.
3. Power off at the wall for about a minute and try again.

On the HDC80E1 condenser dryer, a persistent F4 usually means the heater element has failed or a thermal cut-out has tripped. Both live on the same assembly, and we stock the genuine Fisher & Paykel–Haier condenser dryer heater that suits the HDC80E1 as well as a high-limit thermostat for Haier dryers if the cut-out is the failed part.

On the HDHP80A1 and HDHP80E1 heat pump models, F4 can indicate a refrigerant leak in the sealed system. There is no DIY path here — the refrigeration circuit is a sealed system that only a qualified technician can diagnose and repair, so if the filter and power-cycle checks don’t clear it, book a service call rather than buying parts.

F31, F32 and F33: temperature sensor faults

These three codes all mean a temperature sensor is reading open or short circuit, and Haier scopes them strictly by model — so the code itself tells you which sensor is complaining:

• F31 — HDC80E1 only: the NTC1 sensor near the lint filter.
• F32 — all three digital models: NTC2 near the heater on the condenser model; the condenser/heat-exchanger thermal sensor on the heat pump models.
• F33 — heat pump models only: the condenser/heat-exchanger thermal sensor, documented alongside F32.

The cause is either the thermistor itself or its wiring. Switch off at the wall for about a minute and restart — a one-off glitch won’t return. A persistent F31, F32 or F33 is a technician diagnosis, because confirming sensor versus harness means testing resistance at the board. To see what parts suit your machine before the technician visits, run your model through the Part Finder quiz.

Codes that aren’t faults

E6 is the big one. On the HDC80E1, E6 looks exactly like a fault code — but it’s the filter-clean reminder, not an error. The same reminder shows as “Filter” on the HDHP80A1, “cln LInt” on the HDHP80E1 and a flashing light on vented models. Clean the lint filter (and the condenser filter where fitted) and it goes away. If your foam or mesh filter is torn rather than just clogged, we stock a replacement Haier lint filter for selected models — check yours through the quiz first.

The other displays that send people searching for faults that don’t exist:

• Tank light: the condensate tank is full — condenser and heat pump models only, and heat pump models also pause and beep. Empty the tank and resume, or fit the supplied drain hose so the machine drains automatically.
• Child lock / key lock icon: the control lock is active and the buttons are disabled. It isn’t cleared by the cycle ending or by pulling the plug — hold the two-button combination for about three seconds (Temp + Signal on the HDC80E1; Delay + Time on the HDHP80A1; Dry Level + Anti-crease on vented AWW1 models). The combo varies by model, so check your manual.
• Iron ready icon: the load has reached iron-damp moisture — a notification, not a problem. Take out anything you want to iron, or ignore it.
• Anti-crease icon: the drum turning intermittently after the cycle finishes is the anti-crease phase doing its job.
• END: the cycle is complete — or the load was already dry when it started.

Find the exact part for your model

Every part above is model-specific, and the model number lives on the sticker around the door opening — our Haier model number guide shows exactly where to look, and the general find-your-model page covers every brand we stock. If the sticker has faded past reading, our guide to identifying an old dryer without a model sticker walks you through it. From there, the Part Finder quiz matches your model to the right part in about a minute, or you can browse the full dryer parts range directly.

Related guides: dryer spare parts guide

FAQ

What does F2 mean on a Haier dryer?

F2 is a condensate drain pump error on the HDC80E1, HDHP80A1 and HDHP80E1. Empty the water tank, check the drain hose isn’t kinked or raised above about a metre, and clean the condenser/pump filter area. If F2 returns after those checks and a power-cycle, the pump has usually jammed or failed and needs replacing.

Is E6 on a Haier dryer a fault?

No. E6 on the HDC80E1 is the filter-clean reminder — a maintenance prompt, not an error code. Clean the lint filter and the condenser filter and the display clears. The same reminder appears as “Filter” or “cln LInt” on the heat pump models.

My Haier vented dryer is beeping with the lights off — what code is that?

Vented HDV models don’t have a code table. Continuous beeping with the panel lights off (and a generic number on display models) is Haier’s all-purpose fault signal — record what you see and call service. Before you do, power-cycle at the wall, clean the lint filter and check the exhaust path; if the symptom is damp clothes or hot cut-outs, the exhaust sensor is the most common replaceable part.

Why isn’t E4 or E8 listed for my Haier?

E-series codes like E3, E4 and E8 belong to Haier washer-dryer combo machines, not the standalone dryers this guide covers. If your machine washes as well as dries, its code table is different — don’t apply the F-code diagnoses above to it.

Will unplugging my Haier dryer clear an error code?

Switching off at the wall for about a minute clears the display and resets the boards, and for a one-off glitch that’s the end of it. But a power-cycle doesn’t repair anything — if the same code returns on the next cycle, the underlying fault is real and needs the checks or the part listed above.