Appliance Spares
Quick answer: A loud Samsung washing machine almost always comes down to one of four things: worn drum bearings (a grinding rumble that gets louder as the spin speeds up), tired suspension (banging and knocking as the drum hits the cabinet), a corroded drum spider, or a coin or worn drain pump (rattling during the drain). Dampers, suspension rods and drain pumps are cheap, quick fixes ($30–$60); bearings and spiders are bigger jobs but still a fraction of a new machine. Here’s how to tell which one you’ve got.
Find the right Samsung part by model number
Match the noise to the fault
| What you hear | When | Most likely cause |
|---|---|---|
| Grinding / rumbling, like a jet taking off | Gets louder as the spin speeds up | Worn drum bearings |
| Banging / knocking, drum hitting the sides | During spin, especially with a small load | Worn suspension (dampers or rods) |
| Heavy knocking with vibration | On spin, often with a rust streak in the wash | Corroded drum spider |
| Rattling / clattering | During the drain part of the cycle | Coin in the pump, or a worn drain pump |
| Clicking / buzzing, no spin | Tries to spin then stops | Drain or motor fault — not a noise part |
1. Worn drum bearings (the grinding rumble)
This is the classic Samsung front-loader noise: a rumble on the spin that grows with the speed, sometimes with a little play if you rock the drum by hand. The bearings sit behind the drum and wear out after years of fast spins. Left too long, failed bearings can chew up the shaft, so it’s worth doing once you’re sure. We stock the Samsung lip-seal and bearing kits — around $50–$57 depending on the model (for example the kit for the WW75/WW85 series). It’s the most involved repair here — weigh the labour on a very old machine.
2. Worn suspension (the banging on spin)
If the drum bangs the cabinet on the spin, the suspension has gone soft. On front loaders that’s a pair of damper shock absorbers under the tub — for example the damper shocks for the WW85 series (~$47). On top loaders it’s the four suspension rods that hang the tub — a Samsung suspension rod kit (from ~$39). Both are quick, cheap fixes and an easy DIY.
3. Corroded drum spider (knocking with a rust streak)
The spider is the three-arm alloy casting that bolts the drum to the shaft. On older Samsung front loaders it corrodes, goes loose, and knocks heavily on spin — often leaving a grey or rust mark on the washing. If that’s your symptom, the fix is a Samsung drum spider (from ~$70, model-dependent). It’s a tear-down job, similar effort to bearings.
4. A coin or a worn drain pump (rattling on drain)
A rattle that only happens when the machine pumps out is usually loose change in the pump, or a worn pump impeller. First, unscrew the filter behind the kick panel at the bottom front and clear it — you’ll often find the culprit. If the pump still grinds or hums, replace it: a Samsung drain pump is around $30 and a straightforward swap.
Repair cost summary (Australia 2026)
| Cause | Part cost | Job |
|---|---|---|
| Drain pump / clear a coin | $0–$30 | 30 minutes |
| Suspension rods or dampers | $39–$49 | under an hour |
| Drum bearings (lip-seal kit) | $50–$57 | half-day tear-down |
| Drum spider | $70–$110 | half-day tear-down |
| New Samsung washer | $700–$1,600 | — |
The 50% rule: dampers, rods and pumps are always worth fixing. Bearings and spiders are worth it on a machine that’s otherwise sound — the part is well under a fifth of a new washer.
Frequently asked questions
Why is my Samsung washing machine so loud on the spin cycle?
A rumble that builds with the spin speed is worn drum bearings; banging that comes and goes is the suspension. Rock the empty drum by hand — noticeable play points to bearings or the spider.
Is a noisy Samsung washer worth repairing?
Yes for suspension, dampers and pumps — they’re cheap and quick. For bearings or a spider, it’s worth it if the rest of the machine is sound, since the part is a small fraction of replacement.
My Samsung rattles only when it drains — what is it?
Usually a coin in the drain pump. Clear the filter behind the bottom kick panel first; if it still grinds, the pump needs replacing.
How do I find my Samsung model number?
On the model sticker around the door opening (front loaders) or under the lid (top loaders). Front loaders start with WF or WW; top loaders with WA. Enter it in the Part Finder for the exact-fit part.
Do these parts ship same day?
Yes — order before 12pm Sydney time for same-day dispatch Australia-wide, flat $10.60 shipping.
Related
- Samsung WA11M8700 top loader parts guide
- Samsung WD10F7S7SRP washer-dryer parts guide
- Samsung washing machine repair guide
- All Samsung washing machine parts
- Find your exact part with the Part Finder
Ready to fix it?
- Run your model number through the Oz Appliance Spares Part Finder — model in, exact-fit part out.
- Browse 3,000+ parts in stock
- Order before 12pm Sydney time → ships same day from our Sydney Northern Beaches warehouse, Australia-wide.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
