Appliance Spares
Quick answer: If your InAlto washer won’t drain and leaves water in the drum at the end of the cycle, check the pump filter behind the bottom kick panel first — a trapped coin, clip or sock is the most common cause and clearing it costs nothing. If the filter and hose are clear but the pump only hums or stays silent, the drain pump has failed: it’s a $59.95 part and about a 45-minute DIY job. A blocked or dead pump is the usual reason an InAlto stops draining — not a reason to replace the machine.
InAlto drain pump · find your model
Why an InAlto won’t drain
| Cause | How to spot it |
|---|---|
| Blocked pump filter | Pump tries but water won’t go — a coin or debris in the filter |
| Failed drain pump | Pump hums without pumping, or is silent at the drain step |
| Kinked or blocked drain hose | Hose pinched behind the machine or clogged at the standpipe |
| Blocked filter housing / sump | Slow drain, gunk visible when the filter is removed |
Step 1: Clear the filter (free fix first)
- Unplug at the wall. Have a shallow tray and towels ready — water will come out.
- Open the small hatch on the bottom front of the machine and unscrew the filter cap slowly to drain the water.
- Pull the filter out and clear anything jammed in it and in the housing — coins, clips, lint, the odd sock.
- Refit the filter, plug in, and run a rinse-and-spin. If it drains, you’re done.
While you’re there, check the drain hose at the back isn’t kinked and the standpipe isn’t blocked — both stop a healthy pump from draining.
Step 2: Replace the pump (if it hums or stays silent)
If the filter and hose are clear but the pump just hums or does nothing, the pump motor has failed. Fit a new one:
- Unplug and turn off the taps; drain the machine via the filter first.
- Access the pump — on most InAlto front loaders that’s through the bottom or the rear panel.
- Photograph the wiring, then unclip the connector and release the hose clamps (have a towel ready).
- Unbolt the old pump and fit the new InAlto pump, reconnecting the hoses and wiring exactly as they were.
- Restore power and water and run a rinse-and-spin to check it drains and there are no leaks.
Repair cost summary (Australia 2026)
| Path | Cost | Time |
|---|---|---|
| Clear the filter | Free | 15 min |
| DIY: replacement drain pump | $59.95 | 45 min |
| Professional repair: part + call-out | $190–$270 | 1-hour booking |
| Replacement InAlto washer | $600–$1,000 | — |
Frequently asked questions
Q: My InAlto washer is full of water and won’t drain — what first?
A: Clear the pump filter behind the bottom kick panel — a trapped coin or sock is the most common cause and the fix is free. Only replace the pump if the filter and hose are clear but it still won’t move water.
Q: The pump hums but no water moves — is it dead?
A: A humming pump that doesn’t pump is either jammed (clear the filter) or has a seized impeller (replace it). A silent pump at the drain step is also a replacement.
Q: Why won’t it spin either?
A: An InAlto won’t spin until it has drained, so a drain fault also stops the spin. Fix the drain and the spin usually returns.
Q: Where do I get an InAlto drain pump?
A: We stock it — InAlto (a Winning Appliances house brand) has no parts counter. See the InAlto parts guide.
Q: Same-day dispatch?
A: Yes — order before 12pm Sydney time, same-day dispatch Australia-wide, flat $10.60 shipping.
Related
- InAlto appliance parts — full guide
- Hard-to-find appliance brand parts — full index
- All InAlto parts in stock
Ready to fix it?
- Run your model number through the Oz Appliance Spares Part Finder — model in, exact-fit pump out.
- Browse 5,000+ parts in stock
- Order before 12pm Sydney time → ships same day from our Sydney Northern Beaches warehouse, Australia-wide.
