Appliance Spares
Quick answer: If your Euromaid washer won’t drain and sits full of water at the end of the cycle, start with the pump filter behind the bottom kick panel — a coin, hair clip or sock jams the pump more often than not, and clearing it is free. If the filter’s clear and the pump just hums or stays silent, the drain pump has failed: it’s a $43–$60 part and about a 45-minute DIY job. A blocked or dead pump is the usual reason a Euromaid stops draining — not a reason to replace the machine.
Euromaid drain pump — E750FLW / WMD107 · find your model
Why a Euromaid won’t drain
| Cause | How to spot it |
|---|---|
| Blocked pump filter | Pump tries but water won’t go — a coin or debris in the filter |
| Failed drain pump | Pump hums without pumping, or is silent at the drain step |
| Kinked or blocked drain hose | Hose pinched behind the machine or clogged at the standpipe |
| Blocked filter housing / sump | Slow drain, gunk visible when the filter is removed |
Step 1: Clear the filter (free fix first)
- Unplug at the wall. Have a shallow tray and towels ready — water will come out.
- Open the small hatch on the bottom front of the machine and unscrew the filter cap slowly to drain the water.
- Pull the filter out and clear anything jammed in it and in the housing — coins, clips, lint, the odd sock.
- Refit the filter, plug in, and run a rinse-and-spin. If it drains, you’re done.
While you’re there, check the drain hose at the back isn’t kinked and the standpipe isn’t blocked — both stop a healthy pump from draining.
Step 2: Replace the pump (if it hums or stays silent)
If the filter and hose are clear but the pump just hums or does nothing, the pump motor has failed. Fit a new one:
- Unplug and turn off the taps; drain the machine via the filter first.
- Access the pump — on most Euromaid front loaders that’s through the bottom or the rear panel.
- Photograph the wiring, then unclip the connector and release the hose clamps (have a towel ready).
- Unbolt the old pump and fit the new one, reconnecting the hoses and wiring exactly as they were.
- Restore power and water and run a rinse-and-spin to check it drains and there are no leaks.
Match your model: the E750FLW / WMD107 pump suits the combo and front loaders, while the WMFL8/9 pump fits those models — check your model sticker.
Repair cost summary (Australia 2026)
| Path | Cost | Time |
|---|---|---|
| Clear the filter | Free | 15 min |
| DIY: replacement drain pump | $43–$60 | 45 min |
| Professional repair: part + call-out | $180–$260 | 1-hour booking |
| Replacement Euromaid washer | $500–$900 | — |
Frequently asked questions
Q: My Euromaid washer is full of water and won’t drain — what first?
A: Clear the pump filter behind the bottom kick panel — a trapped coin or sock is the most common cause and the fix is free. Only replace the pump if the filter and hose are clear but it still won’t move water.
Q: The pump hums but no water moves — is it dead?
A: A humming pump that doesn’t pump is either jammed (clear the filter) or has a seized impeller (replace it). A silent pump at the drain step is also a replacement.
Q: Why won’t it spin either?
A: A Euromaid won’t spin until it has drained, so a drain fault also stops the spin. Fix the drain and the spin usually returns.
Q: Where do I get a Euromaid drain pump?
A: We stock them for the E750/WMD/WMFL models — Euromaid has no parts counter. See the Euromaid parts guide.
Q: Same-day dispatch?
A: Yes — order before 12pm Sydney time, same-day dispatch Australia-wide, flat $10.60 shipping.
Related
- Euromaid washing machine parts — full guide
- Hard-to-find appliance brand parts — full index
- All Euromaid parts in stock
Ready to fix it?
- Run your model number through the Oz Appliance Spares Part Finder — model in, exact-fit pump out.
- Browse 3,000+ parts in stock
- Order before 12pm Sydney time → ships same day from our Sydney Northern Beaches warehouse, Australia-wide.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
