Appliance Spares
Quick answer: The common vented-dryer heating element is DGD266 (around $39.95), and it fits the popular Solt, InAlto, Omega, Euromaid and Stirling (Aldi “Tempo”) models. Same-day dispatch from our Sydney warehouse.
Last updated June 2026
If your clothes dryer still tumbles but the air coming out is cold, you have almost certainly lost the heating element. The good news: across a whole group of Australian house and orphan brands — Solt, InAlto, Omega, Euromaid and Stirling — the replacement is the same affordable part. This page tells you exactly which element you need, what it costs, and how to confirm it fits before you order.
Which heating element fits my dryer?
For the common 4–4.5kg vented dryers sold under Solt, InAlto, Omega, Euromaid and Stirling (Aldi’s “Tempo” range), the heating element you want is DGD266. It is rated AC 220–240V, 50–60Hz and sells for around $39.95 AUD each.
These brands look different on the outside, but underneath they share the same vented-dryer design and the same service element. That is why one part number — DGD266 — turns up again and again across all of them, and why it also matches the element designations you will see stamped on the old part or in a manual: GYJ40-88 and GYJ45-68.
Before you order, do one thing: read the model sticker. It is usually on the back panel, around the door opening, or inside the door rim. Match your model number to the cross-reference table below. If your model is listed, DGD266 is your part.
Vented, condenser or heat pump — which has a replaceable element?
Not every dryer heats the same way, and this matters before you buy.
- Vented dryers draw in room air, pass it over a resistance heating element, and the fan blows that hot air through the drum. The damp air is then ducted outside or into the room. This is the simplest design, and it uses a low-cost, easily replaced element — exactly the DGD266 part covered here.
- Condenser dryers also use a heating element, but instead of venting the moist air they pass it through a heat exchanger to condense the water into a tank or drain. Some condenser models use a similar replaceable element; others are more involved. Check your specific model.
- Heat pump dryers do not use a simple resistance element at all. They recycle heat using a refrigerant circuit, much like a reverse-cycle air conditioner. When a heat pump dryer stops heating, the fault is in a different, more expensive set of parts — not a $39.95 element.
So the short version: if you own a vented dryer from one of the brands below, this page is for you. If you own a heat pump model, see the callout further down.
What is element DGD266 and what dryers does it fit?
DGD266 is the resistance heating element used in the common vented dryers from Solt, InAlto, Omega, Euromaid and Stirling (Aldi). It is a coiled wire element housed in a metal duct that bolts to the back of the dryer behind the drum. Power runs through the coil, the coil glows hot, and the fan pushes that heat into the tumbling clothes.
It is rated AC 220–240V, 50–60Hz — standard Australian mains voltage — and the live price is $39.95 each (verified 30 June 2026).
Here is the complete cross-reference. Find your brand, confirm your model number from the model sticker, and order the matching element.
Dryer heating element cross-reference table
| Brand | Models it fits | Element part | Price | Buy |
|---|---|---|---|---|
 Solt / InAlto | DM4KG, GGSVDE45W, IVDE45W, SP11450 | DGD266 — correct fit | $39.95 | Solt / InAlto element |
 Omega / Euromaid | DM4KG, ED45KG, GYJ40-88, GYJ45-68, OCD40WA, OCD4W, OCD6W, SP11450 | DGD266 — correct fit | $39.95 | Omega / Euromaid element |
 Stirling “Tempo” (Aldi) | GYJ40-88, GYJ45-68, OCD40WA, OCD4W, OCD6W, ED45KG, DM4KG | Genuine | $39.95 | Stirling Tempo element |
The same mapping, in plain words
- Solt and InAlto — if your model sticker reads DM4KG, GGSVDE45W, IVDE45W or SP11450, your element is DGD266 at $39.95. This is the listing most customers land on, and it is our default recommendation for these two brands.
- Omega and Euromaid — models DM4KG, ED45KG, OCD40WA, OCD4W, OCD6W and SP11450, plus anything marked GYJ40-88 or GYJ45-68, take the same DGD266 element at $39.95.
- Stirling “Tempo” (Aldi) — the Aldi-sold Stirling dryers using GYJ40-88, GYJ45-68, OCD40WA, OCD4W, OCD6W, ED45KG or DM4KG take the matching element, which we list as Genuine for this brand, also $39.95.
Notice how the model numbers overlap across brands — DM4KG, SP11450, OCD-series, the GYJ designations. That overlap is the whole point: these are rebadged versions of the same vented dryer, so the same element services all of them. We list the Stirling part as Genuine because that is how it is supplied; for the other brands DGD266 is the correct-fit service element. We will not over-claim “genuine” where it does not apply — the part fits and works either way.
Is yours a heat pump dryer instead? If your dryer recycles heat and empties water into a tank rather than venting it outside, you likely have a heat pump or condenser model — and the heater is a different, pricier part. See our companion guides: Omega heat pump dryer not heating and Fisher & Paykel condenser dryer not heating.
How do I know the heating element has failed?
A failed heating element has a very recognisable signature:
- The drum still turns, but the air is cold. The motor and fan run on a separate circuit from the element, so the dryer keeps tumbling even after the element burns through. This is the classic symptom.
- Clothes come out damp after a full cycle, or take two or three cycles to dry.
- No warmth at the vent or door when you put your hand near the outlet a few minutes into a cycle.
- Sometimes you will spot a visible break in the coil when you remove the element — the resistance wire has burnt through at one point.
Before you blame the element, rule out the simple stuff: a blocked lint filter or choked vent ducting causes the dryer to overheat and trip a thermal cut-out, which can mimic a dead element. Clean the filter and clear the vent first. If the air is still stone cold with good airflow, the element is the likely culprit.
A confident DIYer with a multimeter can confirm it: isolate the dryer from power, access the element, and check for continuity across its terminals. An open circuit (no continuity) means the element has failed and DGD266 is your replacement.
How to replace a vented dryer heating element
This is a straightforward repair on these vented models, but it is mains-voltage work — treat it with respect.
- Isolate the dryer from power. Unplug it at the wall. Do not rely on the power switch.
- Access the element. On most of these models the element sits in a duct on the back panel. Remove the rear panel screws to expose it. If your dryer is wall-mounted, take it down and lay it on a stable surface first.
- Photograph the wiring. Before you disconnect anything, take a clear photo so the new element goes back exactly the same way.
- Remove the old element. Disconnect the spade terminals and any thermal cut-out/thermostat fixed to the element housing, then unbolt the element assembly.
- Fit DGD266. Transfer any thermostats or cut-outs to the new element if your model carries them on the element housing, reconnect the wiring to match your photo, and bolt it back in.
- Reassemble and test. Refit the panel, plug in, and run a short warm cycle. You should feel heat within a couple of minutes.
If at any step you are unsure about the wiring, the thermostats, or working near mains voltage, stop and call a qualified appliance technician.
When to call a technician vs DIY
The DGD266 element itself is an inexpensive, well-documented part, and many handy owners and tradies fit it themselves. But honesty matters here: a dryer heating element runs at mains voltage, and the wiring includes thermal safety devices that must go back correctly.
Do it yourself if you are a competent person — comfortable isolating the appliance from power, reading a wiring photo, and using a multimeter to confirm the fault.
Call a qualified appliance technician if you are unsure about the electrical connections, the dryer is hard-wired, the thermostats are involved, or anything else about the machine looks damaged. Tradies across the Northern Beaches order this exact element from us for that reason — it is cheap, it is in stock, and it is a quick job for someone who does it daily.
When in doubt, isolate from power and get a professional. A $39.95 part is never worth an electrical risk.
Frequently asked questions
How much does the DGD266 dryer heating element cost?
It is $39.95 AUD each (price verified live on 30 June 2026). It dispatches same-day from our Sydney warehouse.
Is DGD266 a genuine part?
For the Stirling “Tempo” (Aldi) dryers, we supply and list the element as Genuine. For Solt, InAlto, Omega and Euromaid, DGD266 is the correct-fit service element for those models — it is the right part that fits and works, supplied at $39.95. We do not label it “genuine” for brands where that is not the case.
Will it fit my Solt, Stirling or Omega model?
If your model sticker matches one of the numbers in the table — for example Solt/InAlto GGSVDE45W, IVDE45W, DM4KG, SP11450, or any brand marked GYJ40-88 / GYJ45-68, or the OCD-series Omega/Euromaid/Stirling models — then yes, DGD266 is your element. Always confirm against your model sticker before ordering.
What is the actual difference between these brands?
Very little, mechanically. Solt, InAlto, Omega, Euromaid and Stirling are largely rebadged versions of the same vented dryer platform, which is why the model numbers overlap and the same element services all of them. The badge on the front changes; the heating element does not.
How long does delivery take?
We dispatch same-day from our Sydney warehouse on in-stock orders, so most customers receive the element within a few business days depending on your location.
Can I replace it myself?
Yes, if you are a competent person comfortable with isolating the appliance from power and reconnecting the wiring exactly as it came off. It is a common DIY job on these vented models. If you are unsure about the mains-voltage connections, use a qualified appliance technician.
My dryer empties water into a tank — is this still my part?
Probably not. A water tank usually means a condenser or heat pump dryer, which uses a different heater. See the heat pump and condenser companion guides linked above.
Order your vented dryer heating element
You do not need to guess. Match your model number to the table, then order the DGD266 element for $39.95 with same-day dispatch from our Sydney warehouse:
- Solt / InAlto vented dryer heating element — DM4KG, GGSVDE45W, IVDE45W, SP11450
- Omega / Euromaid dryer heater element — DM4KG, ED45KG, OCD40WA, OCD4W, OCD6W, SP11450, GYJ40-88, GYJ45-68
- Genuine Stirling “Tempo” (Aldi) dryer heating element — GYJ40-88, GYJ45-68, OCD40WA, OCD4W, OCD6W, ED45KG, DM4KG
Still not sure which one is yours? Browse the full dryer parts store or use our part finder quiz and we will point you to the exact element. Get your dryer blowing hot again this week — not next month.
**Order the Solt / InAlto DGD266 element — $39.95, same-day Sydney dispatch →**
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
