Appliance Spares
Quick answer: The most common faults on the Hisense HWFL1014V are worn drum bearings ($66.55 for the lip seal and bearings kit), a leaking or perished door gasket seal ($72.95), and a failed drain pump ($69.95). All three are in-stock parts available for next-day dispatch from Sydney’s Northern Beaches.
Not sure which one fits? Match your model number or check the sticker inside the door.
The part that fixes this
- Hisense 10kg Washing Machine Lip Seal & Bearings Kit HWFL1014V, HWFE1014VA 0177Q
- Hisense 10KG Washing Machine Door Gasket Seal Suits HWFL1014V HWFE1014VA
- Hisense washing Machine Drain pump HWFL1014V
Not sure it is the same on your machine? See every part listed by Hisense model number.
Last updated September 2026
Lip Seal & Bearings Kit — $66.55 ·
Door Gasket Seal — $72.95 ·
Drain Pump — $69.95 ·
Drum Drive Belt — $34.95 ·
Door Lock Switch — $37.95 ·
Door Hinge — $55.95 ·
Not sure which part? Use the Part Finder
Common faults on the Hisense HWFL1014V
The Hisense HWFL1014V is a 10 kg front-load washing machine, one of the larger-capacity front loaders Hisense sells in Australia. Big family-sized loads put more strain on the drum bearings, drive belt, and door seal than a smaller machine sees, so those wear points tend to show up predictably over its service life. The drum bearings, door gasket seal, and drain pump are the three items most likely to need attention after several years of regular use. Identifying the fault early — before water damage or a seized drum makes the repair harder — saves both money and time.
Before ordering parts, locate the model sticker on the door jamb (the frame exposed when you open the door). Confirm the full model number is HWFL1014V, as Hisense produces several similar-looking machines with different drum sizes and minor component variations — most parts on this page also suit the closely related HWFE1014VA.
| Part | Symptom | Price | Link |
|---|---|---|---|
 Bearing + lip seal kit | Loud grinding or rumbling noise during the spin cycle; excessive vibration even on a balanced load; bearing noise that worsens over time | $66.55 | Buy bearing kit |
 Door gasket seal | Water leaking from the front of the machine during the wash cycle; visible black mould growth on the rubber gasket; cracking or tearing of the boot seal | $72.95 | Buy door gasket seal |
 Drain pump | Water remaining in the drum at the end of the cycle; machine pausing mid-cycle without draining; humming from the pump area but no water movement | $69.95 | Buy drain pump |
 Drum drive belt | Drum not turning while the motor runs; squealing on start-up or during spin; washing still soaked because the drum never reached spin speed | $34.95 | Buy drive belt |
 Door lock interlock switch | Door won’t lock at the start of a cycle; machine refuses to start; door LED flashing; door feels loose on closing | $37.95 | Buy door lock switch |
 Door hinge | Door sagging or not sitting square in the opening; door rubbing on the cabinet when opening; door not sealing evenly against the gasket | $55.95 | Buy door hinge |
Diagnosis guide – Hisense HWFL1014V
- Note any error code first. If the display is showing a code, write it down before attempting anything else. A drain-related code points to the pump or a blocked filter; a door code points to the interlock switch. The code narrows the field immediately.
- Listen during the spin cycle. A low-frequency grinding or rumbling that increases with drum speed points to worn drum bearings. The noise originates from the back of the machine. If the rumbling started gradually and has been getting worse, the lip seal has likely already failed and water has entered the bearing housing.
- Test the door seal visually. Run your fingers around the entire circumference of the rubber boot, paying attention to the lower section at the six o’clock position where water pools. Any crack, split, or visible mould penetration deeper than the surface layer means the seal should be replaced.
- Check for standing water after the cycle. If the drum still has water when the cycle ends, check the drain pump filter first — it is behind the small access panel at the lower front of the machine. Remove and clean it. If the filter is clear and water is still not draining, the pump itself has failed.
- Check the drum turns with the motor. If the motor is audibly running but the drum stays still, or you hear squealing under load, the drive belt has stretched, slipped off the pulley, or snapped. Spin the drum by hand — if it spins with no resistance at all, the belt is off or broken.
- Test the door lock. Close the door firmly and press Start. If the machine does not proceed to the fill stage and the door LED flashes, the door interlock switch has failed. The latch mechanism can also wear, so inspect both the door hook and the switch.
Fitting the parts yourself
The Hisense HWFL1014V is a front-loader, which means some repairs require more disassembly than a top-loader equivalent. Replacing the door gasket seal is a straightforward job that most people with basic tool skills can complete in under an hour — the main requirement is patience when reseating the outer retaining spring clip. Replacing the drain pump, drive belt, door lock switch, or door hinge is similarly accessible via the front, rear, or lower panels.
Bearing replacement is the most involved repair on any front-load machine, and on a 10 kg drum it is heavier work than on a compact model. It requires splitting the outer drum shell, pressing out the old bearings, and fitting new ones — a job that takes 90 minutes to two hours and benefits from having a bearing press or a set of sockets to drive the new bearings home evenly. If you have not done it before, watching a video walkthrough before starting is worthwhile. If you’d prefer a technician to handle it, the bearing kit price means the parts cost is still modest — only the labour varies.
Frequently asked questions
Why is my Hisense HWFL1014V loud on spin?
A grinding or jet-engine rumble that gets louder as the drum speeds up is the classic sign of worn drum bearings. On a 10 kg machine the extra load accelerates bearing wear once the lip seal starts letting water through. The lip seal and bearings kit listed above replaces both in one job.
Can I use HWFE1014VA parts in my HWFL1014V?
Yes — the bearing kit, door gasket seal, drive belt, door lock switch, and door hinge listed above are all confirmed to suit both the HWFL1014V and the HWFE1014VA. Always match the listing’s fitment list to the model number on your model sticker before ordering.
How long should a Hisense HWFL1014V door seal last?
Under normal Australian household use, a door seal typically lasts six to ten years. Seals deteriorate faster if the door is left closed between washes (trapping moisture), if the machine is used frequently with high-temperature cycles, or if the machine is in a humid laundry environment. Wiping the seal dry after each wash extends its life significantly.
Where is the model sticker on a Hisense HWFL1014V?
The model sticker is located on the door jamb — the frame that is exposed when you open the washing machine door. It lists the full model number, serial number, voltage rating, and load capacity. Always confirm the model number from the sticker before ordering parts.
Is it worth repairing a HWFL1014V or should I replace it?
Large-capacity front loaders cost noticeably more to replace than standard models, which tilts the maths further towards repair. For the common faults — door seal, drain pump, drive belt, door lock switch — the part is well under a hundred dollars. Even a bearing replacement, the most labour-intensive repair, is economical if the drum and cabinet are otherwise in good condition.
Related
- Hisense HWFE1014VA parts
- Hisense HWFY1014 parts
- Hisense HWFS8014AB parts
- Part Finder Quiz — enter your model number for matched results
- Browse all HWFL1014V parts
Ready to fix it?
- Locate the model sticker on your door jamb and confirm the model is HWFL1014V.
- Note the fault or error code displayed on the machine.
- Select the matching part from the table above, or use the Part Finder if you’re unsure.
- Add to cart at ozappliancespares.com.au — orders placed before the daily cut-off ship same day from Sydney’s Northern Beaches.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
