Haier Washing Machine Not Filling With Water: The Fix

Quick answer: A Haier washer that won’t fill is nearly always the water inlet valve — from $14.70 on the HWMP top loaders to $98.95 for the washer-dryer combo valve assemblies. Do the free checks first (taps fully on, hoses unkinked, the little mesh screens at the valve rinsed clean), then swap the valve: it’s a 30-minute screwdriver job. A machine that fills erratically rather than not at all usually wants the water level sensor ($25.95–$29.95) instead.

Find the right Haier part by model number — or start at the complete Haier washing machine repair guide.

Match the symptom to the cause

What you see	Most likely cause	Cost to fix
No water at all, or a fill error on the display	Tap, hose or screens — then a failed inlet valve	$0–$98.95
Fills at a dribble, cycle stretches out	Silted mesh screens or a weak valve coil	$0–$57.95
Overfills, underfills, or keeps topping up	Water level sensor misreading	$25.95–$29.95
Water creeps in with the machine switched off	Valve jammed open by grit — replace it promptly	$14.70–$98.95
Washer-dryer combo won’t fill on certain programs	Multi-way electromagnetic valve, one port dead	$69.95–$98.95

Not sure which part?Enter your model number and the Part Finder returns only parts confirmed to fit.

Find my part

Step 1: The free fixes (five minutes)

Turn the taps hard on and straighten the hoses. Then unscrew the inlet hoses at the machine and rinse the small mesh screens sitting just inside the valve inlets — grit and scale collect there gradually, which is why the fill got slower over months before it stopped. Refit and test. Our inlet valve test and replace how-to shows every step with photos.

Step 2: Confirm the valve has died

Start a fill and listen at the back corner. A live valve clicks and hums; silence with good tap pressure means the coil is open-circuit, and no cleaning will revive it. Haier valves are model-specific, so match yours below or run your model number through the Part Finder.

Your Haier machine	Part	Price
HWMP50F, HWMP60TLF top loaders	Haier water inlet valve for HWMP50F and HWMP60TLF	$14.70
HWMP65-918, HWMP75-918 top loaders	Genuine Haier cold inlet valve for HWMP-918 models	$34.85
HWT10MW1/HWT10MW2 10kg top loaders	Haier 10kg top load cold inlet valve	$57.95
HWF10AN1, HWF10ANB1 front loaders	Haier electromagnetic inlet valve for HWF10AN1 and HWF10ANB1	$69.95
HWD9050AN1 washer-dryer combo	Haier washer-dryer combo electromagnetic valve	$98.95

The swap: unplug the machine, taps off, remove the top or rear panel, photograph the wiring, move the spade connectors and outlet hoses to the new valve, and screw it home. Thirty minutes with a screwdriver and pliers.

Step 3: Erratic filling? It’s the level sensor

When water flows fine but the machine overfills, underfills or keeps topping up, the level sensor is feeding the board bad numbers. Front loaders (HWF75–HWF12D families) take the Haier pressure switch ($29.95); HWT top loaders use the Haier water level sensor for HWT07–HWT10 ($25.95). Check the clear sensing hose for splits or kinks before you condemn the sensor — the hose fails for free.

Repair cost vs a service call (Australia 2026)

Option	Typical cost
Clean the screens and hoses yourself	$0
DIY inlet valve (top loaders)	$14.70–$57.95
DIY inlet valve (front loader / combo)	$69.95–$98.95
DIY water level sensor	$25.95–$29.95
Repairer callout plus the same part and labour	commonly $180–$300
New Haier washer	$600–$1,400

Frequently asked questions

Why is my Haier washing machine not filling with water?

In order: a tap not fully open, a kinked inlet hose, blocked mesh screens at the valve, then a failed inlet valve. The free checks take five minutes; Haier valves start at $14.70.

My Haier fills very slowly — same fix?

Usually, yes. A slow fill is the screens silting up or the valve coil weakening. Clean the screens first; if the dribble continues, replace the valve.

The machine keeps topping up during the wash. What is that?

The water level sensor (pressure switch) has drifted, so the board never believes the drum is full. It’s a $25.95–$29.95 part and a 20-minute swap under the top panel.

How do I find my Haier model number?

On the model sticker around the door opening (front loaders) or under the lid (top loaders) — it starts with HWF, HWT, HWMP or HWD. Enter it in the Part Finder for the exact-fit valve.

Do these parts ship same day?

Yes — order by 12pm Sydney time for same-day dispatch Australia-wide.

Ready to fix it?

Run your model number through the Oz Appliance Spares Part Finder — model in, exact-fit part out.
Browse thousands of parts in stock
Order by 12pm Sydney time → ships same day from our Sydney Northern Beaches warehouse, Australia-wide.

Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.