Appliance Spares
Quick answer: A Haier washing machine heating element (heater) heats the water in a washer or dishwasher, or the air in a dryer. The first sign of failure is usually this: clothes are wet and cold at the end of a dryer cycle, but the drum turns. Replacement heating elements for Haier washing machines run about $30–40; an element is a mid-priced part and usually the whole fix. Match the full model number on your Haier sticker (HWF10AN1, HWF10ANB1, HWF10BW1, HWF10DW1 and more) against the listing title before you order.
HAIER WASHING MACHINE HEATER ELEMENT HWF85AW1, HWF85BW1 HWM80-1401, HWM80-1403DIn stock · Sydney warehouseView part- HAIER WASHING MACHINE HEATER ELEMENT HWM85-1479 HWM85-1482 HWM75-1279 HWX8040DW1In stock · Sydney warehouseView part
- Haier H0024000279 Washing Machine Heater element HWM80-1403D HWF75AW2In stock · Sydney warehouseView part
- Haier Washing Machine Heater element HWF10AN1, HWF10ANB1, HWF10BW1, HWF10DW1In stock · Sydney warehouseView part
- Haier Washing Machine Heater element HWF70BW1, HWF75AN1, HWF75AW3, HWF80AN1In stock · Sydney warehouseView part
- Haier Washing Machine Heater element HWF80ANB1, HWF85AN1, HWF85ANB1, HWF90AN1In stock · Sydney warehouseView part
- Haier Washing Machine Heater element HWF90ANB1, HWF90BW1, HWF95AN1, HWF95ANB1In stock · Sydney warehouseView part
- 2 x Haier Washing Machine lint Filters HWT10AD1 HWT10ADB1 HWT10AN1 HWT10ANB1In stock · Sydney warehouseView part
- Haier H00330510003A Washing Machine Switch Water Level Sensor HWT60AA1In stock · Sydney warehouseView part
Fit check: the model number on your sticker must appear in the listing title — the badge on the front is not enough. All washing machine parts · Not listed? Send us the model number and we match it before you pay.
Last updated October 2026
What the heating element does on a Haier washing machine
The heating element heats the water in a washer or dishwasher, or the air in a dryer. On Haier washing machines sold in Australia the same part is shared across model families, which is why one listing covers several model numbers, and why two heating elements that look alike are not interchangeable: the mounting, the plug and the signal differ between families. The full model number on your sticker settles it.
Isolate at the wall before you touch terminals. 240 V work on a hard-wired appliance is for a licensed person.
Symptoms of a failed Haier heating element
| What you see | What it usually means |
|---|---|
| Clothes are wet and cold at the end of a dryer cycle, but the drum turns | The element is open-circuit or a thermal fuse has blown |
| The wash runs cold on a hot program | The element has failed, or the thermistor is not reading |
| A heating error on the display | The board cannot see the element drawing power |
| A burnt smell and then no heat | A broken coil or a failed thermal cut-out |
Is it really the heating element?
On a dryer, a blocked lint filter or vent trips the thermal cut-out long before the element fails; clean them both and reset or replace the cut-out first. On a washer or dishwasher, a scaled element still heats slowly, so run a descaler before you condemn it. Test the element for continuity before you buy.
Where is the model sticker on a Haier washing machine
Inside the door opening, on the rim, or behind the detergent drawer. Write the full code down, letters and numbers, or photograph it: the suffix matters, and the badge on the front of the machine is not enough. Our Haier model number guide has photos of each spot.
Which Haier heating element is listed for your model
One row per model number as it appears on the sticker. The part column is the listing title, which names every model that listing covers.
HWF10AN1
HWF10ANB1
HWF70BW1
HWF75AW2
HWF80ANB1
HWF85AW1
HWF90ANB1
HWM75-1279Model not in the table? Send us the full model number and we check the heating element against it before you pay.
Replacing the heating element: the job in order
- Pull the plug. Dryer: remove the back or front panel to reach the heater box. Washer and dishwasher: the element sits in the bottom of the tub, reached from behind or below.
- Photograph the terminals and any thermostats on the element before you unplug anything.
- Release the terminals and the fixing nut or screws, and draw the element out.
- Install the new element with its seal, tighten evenly, and reinstall the terminals and thermostats.
- Plug in and run a short cycle; check for heat and, on a tub element, for leaks around the seal.
DIY or a repairer?
For most people this is a DIY job: an element is a mid-priced part and usually the whole fix. A repairer’s call-out in Australia is in the $100–165 band before the part, so the saving is the labour. Use a licensed repairer if the appliance is hard-wired, if you find burnt or melted wiring, if gas or sealed refrigerant is involved, or if the new part does not cure the fault, because the next suspect is usually the control board and that is fitted after diagnosis, not before.
Frequently asked questions
The dryer runs but blows cold. Element or something else?
Clean the lint filter and the vent first, then look for a thermal cut-out on the heater box: many have a small reset button. If the cut-out is fine and the element shows no continuity, it is the element. If the element is good, the thermostat or the board is next.
Do I need a repairer?
Element work is 240 V. If you are not confident testing and reconnecting terminals, use a repairer. Hard-wired appliances are always a repairer's job.
Is it the same element across the range?
No. Wattage, shape and terminal layout differ. Match the full model number on your sticker against the listing title.
Why did it fail?
Age, scale, and on dryers a choked vent running the element hot. Keep the filter and vent clear.
The new element trips the power. Why?
Water in the heater box, a damaged seal, or a wiring fault. Stop and have it checked.
How fast does a Haier heating element arrive?
Parts in stock in Sydney are dispatched the day you order when it’s in by 12pm Sydney time, with $10.60 flat delivery Australia-wide and free delivery over $149. Most of Australia sees the part within a few business days.
Get the right heating element first time
Photograph the sticker, match the full model number against the listing title, and if anything is unclear send us the code. In stock in Sydney and dispatched the day you order when it’s in by 12pm Sydney time. Browse all washing machine parts or the brand shelves.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
