Appliance Spares
Quick answer: The most common faults on Simpson SWF front loaders (SWF14843, SWF12743, SWF12843, SWF10732, SWF10761) — which share their platform with Electrolux EWW machines — are worn drum bearings ($48.95–$56.95 for the kit), a failed door lock switch ($33.95), and a faulty inlet valve ($34.85). All are in-stock parts shipped from Sydney’s Northern Beaches.
Not sure which one fits? Match your model number or check the sticker inside the door.
Bearing Seal Kit (SWF14843) — $56.95 ·
Bearings Seal Kit (SWF10732 / SWF10761 / SWF12743) — $48.95 ·
Bearings & Seal Set (EWW14912 / EWW14013 / SWF14843) — $56.95 ·
Door Lock Switch — $33.95 ·
Dual Inlet Valve — $34.85 ·
Inlet Valve (SWF85562 / SWF12743 / SWF12843) — $39.95 ·
Drum Drive Belt 5PJE1196 — $19.93 ·
Not sure which part? Use the Part Finder
Common faults on Simpson SWF front loaders
Simpson’s SWF front loaders — SWF14843, SWF12743, SWF12843, SWF10732, SWF10761, SWF10832 and SWF85562 — are built on a platform shared with Electrolux machines such as the EWW14912 and EWW14013, which is why several parts below carry both brands in their fitment lists. If you own one of these machines, the parts interchange works in your favour: the same bearing kits, lock switches and valves service the whole platform. The signature fault is drum bearing wear — a rumble on spin that builds over time — followed by the door lock switch and the water inlet valves.
Before ordering parts, locate the model sticker on the door jamb (the frame exposed when you open the door). Simpson model numbers within this family differ by one or two digits between capacities, and the bearing kits are split by model group, so confirm your exact model number against the fitment list before ordering.
| Part | Symptom | Price | Link |
|---|---|---|---|
 Bearing seal kit (SWF14843) | Loud grinding or rumbling during spin that worsens over time; excessive vibration on a balanced load; play in the drum when lifted by hand | $56.95 | Buy bearing seal kit |
 Bearings seal kit (SWF10732, SWF10761, SWF12743) | Same bearing rumble on the smaller SWF models — kit includes bearings and lip seal in one job lot | $48.95 | Buy bearings seal kit |
 Bearings & seal set (EWW14912, EWW14013, SWF14843) | The Electrolux-branded set for the shared platform — same fitment as the SWF14843 kit, listed under both brands | $56.95 | Buy bearings & seal set |
 Door lock switch (SWF12743, SWF12843, SWF14743) | Door won’t lock at the start of a cycle; machine refuses to start; door stays locked after the cycle finishes | $33.95 | Buy door lock switch 8084553018 |
 Dual inlet valve (SWF12743, SWF12843, SWF10761) | Machine not filling or filling very slowly; filling when switched off; fill fault on the display | $34.85 | Buy dual inlet valve |
 Inlet valve (SWF85562, SWF12743, SWF12843) | Alternative valve fitment for these model numbers — match the fitment list to your model sticker before choosing between the two valves | $39.95 | Buy inlet valve |
 Drum drive belt (SWF10732, SWF12743, 45S651D) | Drum not turning while the motor runs; squealing on start-up; washing still soaked because the drum never reached spin speed | $19.93 | Buy drive belt 5PJE1196 |
Diagnosis guide – Simpson SWF / Electrolux EWW platform
- Listen during the spin cycle. A low grinding or rumbling that rises with drum speed is the classic bearing failure on this platform. It starts subtle and builds over weeks. Lift the inner drum by hand with the door open — noticeable play or a clunk confirms it.
- Note any fault code. If the display shows a code, record it before switching the machine off. The Westinghouse, Simpson and Electrolux error code guide translates the shared platform’s codes — fill codes point to the valves, drain codes to the pump filter, door codes to the lock switch.
- Test the door lock. Close the door firmly and press Start. If the machine never clicks the lock in and refuses to fill, the door lock switch has failed. The same switch also causes a door that stays locked long after the cycle ends.
- Watch the fill. Slow filling with good tap pressure, or water creeping in while the machine is off, points to the inlet valve. Two valves cover this family — check which one lists your exact model before ordering.
- Check for standing water after the cycle. Clean the drain pump filter behind the lower front panel before ordering anything — lint and coins stop these machines draining far more often than the pump fails. The Electrolux not-draining guide applies to the shared platform.
- Check the drum turns with the motor. If the motor runs but the drum stays still, or it squeals under load, the drive belt has stretched or come off. Spin the drum by hand — no resistance means the belt is off or broken.
Fitting the parts yourself
The door lock switch, inlet valves and drive belt are all straightforward repairs on this platform. The lock switch is reached by peeling back the door seal lip and removing two screws; the valves sit just inside the rear top panel where the hoses connect; the belt walks onto the pulley from the rear. Each job takes well under an hour with basic hand tools. Unplug the machine and isolate the taps before starting.
Bearing replacement is the involved one: the tub comes out and gets split, the old bearings are pressed out, and the new ones must be driven in square. Allow 90 minutes to two hours and read a walkthrough first. Every kit above includes the lip seal — always fit it with the new bearings, because a worn seal letting water into the bearing housing is what kills the bearings in the first place. If the job is more than you want to take on, a technician can fit the kit while the parts cost stays under sixty dollars.
Frequently asked questions
Are Simpson SWF and Electrolux EWW parts interchangeable?
On this platform, frequently yes — the bearing set listed for EWW14912 and EWW14013 also lists the SWF14843, because the machines share their mechanical platform. Always confirm your exact model number appears in the listing’s fitment before ordering, as not every part crosses over.
Why is my Simpson front loader loud on spin?
Worn drum bearings. It is the signature fault of this family: a rumble that builds with drum speed and gets worse over time. The bearing kits above are split by model group — SWF14843 takes one kit, SWF10732/SWF10761/SWF12743 another — so match your model sticker before ordering.
Which inlet valve does my SWF need?
Two valves cover the family and their fitment overlaps on some models. Check both listings against the full model number on your model sticker; if your machine appears in both, either listed valve suits it. If you are unsure, run your model number through the Part Finder.
Where is the model sticker on a Simpson front loader?
On the door jamb — the frame exposed when you open the washing machine door. It lists the full model and serial number. Read it directly rather than relying on the machine’s marketing name, as several SWF variants look identical from the front.
Is an older SWF worth repairing?
Usually, yes. These machines are mechanically simple and every part on this page is under $60. A bearing kit plus a weekend of work — or a single technician visit — keeps the machine going for years, which is hard to beat against the cost of a new front loader of similar capacity.
Related
- Westinghouse, Simpson and Electrolux washing machine error codes
- Electrolux front loader loud on spin — bearings and seal kit fix
- Electrolux washing machine not draining — which part fixes it
- Part Finder Quiz — enter your model number for matched results
- Browse all SWF14843 parts
- Browse all SWF12743 parts
Ready to fix it?
- Locate the model sticker on your door jamb and confirm your exact SWF (or EWW) model number.
- Note the fault or error code displayed on the machine.
- Select the matching part from the table above, or use the Part Finder if you’re unsure.
- Add to cart at ozappliancespares.com.au — orders placed before the daily cut-off ship same day from Sydney’s Northern Beaches.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
