
Quick answer: Ariston washing machines (and Hotpoint and Indesit, which share the platform) show F-codes. F01 is the motor control (triac), F02 the motor or tacho, F03 the wash temperature sensor, F04 and F05 the pressure switch stuck empty or full, F06 the program selector, F07 and F08 the heater relay, F09 the memory, F10 the pressure switch, F11 the drain pump, F12 a communication fault, F13 to F15 washer-dryer heating faults, F17 the door lock relay and F18 an internal data error. Clean the filter and check the hoses; a code that returns names the part.
Not sure which one fits? Match your model number or check the sticker inside the door.
Every brand’s error codes in one index · Find your exact part
Last updated September 2026
Ariston, Hotpoint and Indesit washing machines are built by the same group on the same control platform, so their fault codes are one list. The board watches the motor, the heater, the water level, the door lock and its own memory, and stops with an F-number when a check fails. On models without a display the number is shown as a pattern of flashing lights that the manual decodes.
This guide covers the Ariston front loaders and washer-dryers sold in Australia, including the Aqualtis, Hotpoint-Ariston and older Margherita platforms, and applies equally to Hotpoint and Indesit badges. For each code you get the plain meaning, the likely cause and the part or check that clears it. Most of the common ones are the drain pump, the pressure switch and the motor’s carbon brushes, and all three are home-fit parts.
Ariston washing machine error codes: quick-reference table
Codes are listed as they appear on the display. Where two generations of the platform use different codes for the same fault, both are shown. Always confirm against the manual for your exact model before ordering a part.
| Code | What it means | Most likely cause | What to do / the part |
|---|---|---|---|
| F01 | Motor control (triac) short circuit | Water on the board, motor fault feeding back | Power off at the wall; a repeat is a board repair |
| F02 | Motor jammed or tacho not reading | Bearings seized, foreign object between drum and tub, tacho coil loose, carbon brushes worn | Turn the drum by hand; reseat the tacho; replace worn carbon brushes or the motor |
| F03 | Wash temperature sensor open or short | Sensor failed, connector corroded | Replace the temperature sensor |
| F04 | Pressure switch stuck on empty (machine thinks it is empty when full) | Blocked pressure hose, pressure switch failed | Clear the pressure hose; replace the pressure switch |
| F05 | Pressure switch stuck on full, or water not drained | Blocked filter, drain pump failed, pressure switch | Clean the filter; check the pump; replace the pressure switch if the drum is empty |
| F06 | Program selector or button fault | Selector worn, water behind the panel | Dry the panel; replace the selector or control if it repeats |
F07 | Heater relay stuck on, or heater not detected under water | Heater relay welded, heater open, pressure switch | Test the heater for continuity; board repair if the heater is fine — fit the Indesit Washing Machine Heating Element SIXL126 SIXL106 0113 |
| F08 | Heater relay cannot be activated | Heater open circuit, relay failed, pressure switch reading empty | Replace the heater if open; otherwise board repair |
| F09 | Incompatible or corrupt memory (EEPROM) | Board fault | Power off at the wall for a minute; a repeat needs the board reprogrammed |
| F10 | Pressure switch not sensing correctly | Pressure switch or its hose | Clear the hose; replace the pressure switch |
| F11 | Drain pump cannot be activated | Pump coil open, connector loose, pump seized | Check the connector; replace the drain pump |
| F12 | Communication fault between the control and display boards | Loose ribbon cable, moisture, board fault | Power-cycle; check the connector; service if it repeats |
| F13 / F14 / F15 | Washer-dryer drying faults: fan or temperature sensor (F13), dryer heater (F14), dryer heater relay (F15) | Drying element or sensor, relay on the board | Test the dryer element; replace it or the sensor |
| F16 | Drum lock fault (top loaders) | Drum lock not engaging | Position the drum correctly; service if it repeats |
| F17 | Door lock relay or door lock fault | Door lock failed, relay welded | Replace the door lock; board if it repeats |
| F18 | Internal data error | Board firmware | Power off at the wall for a minute; service if it repeats |
| Door | Door not closed | Door open or item trapped | Close firmly |
H2O | No water arriving | Tap off, hose kinked, screen blocked, inlet valve | Open the tap, clean the screen; replace the inlet valve — fit the Ariston Washer 2 Way Water Inlet Solenoid Valve |
Reading the code on a machine without a display
Older Ariston and Indesit machines show faults by flashing the program lights and the on/off light. Count the flashes and match the number to the F-code: eleven flashes is F11, for example. Some models flash the door lock light at the same time. If you cannot read the pattern, the symptom column of the table gets you there: water left in the drum is F05 or F11, cold washing is F07 or F08, a motor that hums and does not turn is F02.
F02: the drum will not turn
F02 is the code owners see most on older Aristons and it is usually the motor’s carbon brushes, worn to nothing after ten or more years. The symptoms are a machine that fills and drains but never tumbles, sometimes with a smell of hot dust. Replacing the brushes is a rear-panel job. If the brushes are long, turn the drum by hand: a seized bearing or a bra wire between drum and tub will also stop it, and the tacho coil on the end of the motor can work loose and give the same code.
F05 and F11: the drain pump
F05 is the board seeing water still in the drum after the drain phase; F11 is the pump not answering at all. Both start behind the small flap at the bottom front: drain the machine through the emergency hose, unscrew the filter and clear coins and lint, check the impeller behind it turns freely. A pump that hums without turning is jammed or seized; a silent pump with F11 has an open coil. Either way the drain pump is a plug-in swap held by three screws.
Ariston washing machine parts in stock in Sydney
These are the parts behind the codes above that we hold in stock and ship Australia-wide. Match the model number on your model sticker before ordering, or run it through the Part Finder and let it match for you. Every part we hold for the brand is listed on the Ariston parts page, and by model on the model pages; the wider range is in the washing machine parts store.
- Indesit Washing Machine Heating Element SIXL126 SIXL106 0113
- Ariston Washer 2 Way Water Inlet Solenoid Valve
- Hisense Washing Machine Door Seal HCF7S1014B/BX HWF9S1214BX
- Hisense Washing Machine Door Seal HWF3S7514X HWF3S8514X
- Omega 9 kg Front Load Washing Machine Door Seal — Suits OWM9W
- Omega 7.5 kg Front Load Washing Machine Door Seal — Suits OWM75W
- Hisense Washing Machine Door Seal — Part
- Hisense Washing Machine Door Seal — Part
Is it safe to fix an error code yourself?
Most of the codes above are cleared with a filter clean, a hose check or a plug-in part swap, and those are ordinary DIY jobs: unplug the machine, photograph the wiring before you unplug anything, and never bypass a door lock or a thermal cut-out. Anything involving the sealed refrigerant circuit, gas, or a mains-side repair belongs with a licensed repairer.
Frequently asked questions
How do I reset a Ariston washing machine error code?
Switch the machine off, turn it off at the wall for one minute, then restart the program. A code that returns as soon as the machine reaches the same step is a real fault and needs the check or part in the table.
What does F02 mean on an Ariston washing machine?
The motor is jammed or its speed sensor is not reading. On older machines it is usually worn carbon brushes; also check the drum turns freely by hand and the tacho coil is seated.
What does F05 mean?
Water was not drained: the pressure switch still reads full after the drain phase. Clean the pump filter, check the hose and the pump impeller, and replace the drain pump if it hums without moving water.
What does F08 mean on a Hotpoint or Ariston?
The heater relay could not be activated, which usually means the heating element has gone open circuit. Test the element and replace it if it reads open.
Are Hotpoint and Indesit codes the same as Ariston?
Yes. All three brands use the same control platform and the same F-code list.
Where is the model number on a Ariston washing machine?
Open the door and look at the sticker on the inside of the door rim or on the frame behind the door. The model reads like AQ113D or RSG 845. Use it to match parts or run it through our Part Finder.
Read the code, then fit the part
Brushes, pump, pressure switch: the three parts behind most Ariston codes, and all three are home-fit. Find your Ariston part now
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
Appliance Spares




F07
H2O



