
Quick answer: When a Whirlpool belt-drive top loader stops, it is almost always one of four cheap parts. Won’t drain: the 3363394 pump, or the 1515007/200937P on later machines. Barely agitates: the 285811 agitator dogs and cam kit. Fills then sits silent: the 3949247 lid switch. Timer knob spinning uselessly: 3364291 white or 3956905 black. All sit in the $12–50 band and swap with hand tools. Match the model number on the sticker under the lid — that is what decides the part.
Last updated August 2026
The machine that refuses to die
The classic American-style Whirlpool top loader — big square cabinet, deep basket, a mechanical timer you pull to start — went out of fashion around the same time as the Hills Hoist, and like the Hills Hoist it still works. Plenty of Australian laundries, garages and rentals are running one that is twenty-plus years old, and its Amana and Maytag cousins share much of the same hardware underneath.
These machines fail politely. There is no control board to die and no error code to decode. When one stops, it is nearly always a small mechanical part worn out after a few thousand loads. Before you order anything, find the model sticker — under the lid or on the top rim of the cabinet on most machines. The model number, not the badge, decides the part.
Four symptoms, four parts
Start with what the machine is doing. Each listing names the machines it covers — check yours against the model sticker.
| Symptom | What it means | The part |
|---|---|---|
Wash finishes but the water just sits there | The drain pump has seized or the impeller has stripped | Whirlpool top loader drain pump 3363394 |
Won’t drain, and yours is a later machine (Whirlpool, Amana or Maytag) | The direct-drive era uses a different pump | Whirlpool Amana Maytag direct-drive pump 1515007 200937P |
Fills, then sits in silence — or washes but refuses to spin | The lid switch is no longer making contact | Whirlpool lid switch 3949247 (flat pins) |
Top half of the agitator flops or ratchets freely both ways | The four plastic agitator dogs have worn smooth | Whirlpool agitator dogs and cam kit 285811 |
Timer knob spins without starting anything, or has split in half | The knob’s splines have stripped on the timer shaft | Whirlpool timer knob 3364291 (white) |
Won’t drain: the pump
The cycle ends, the lid comes up, and the basket is still full of grey water. Before you blame the pump, unplug the machine and do the free checks: a kinked outlet hose behind the machine, or a sock, coin or bra wire jammed at the pump inlet. Clear those and run a drain. Still sitting full? The pump is done — on a machine this age the impeller strips or the bearing seizes, and it is a replace-not-repair part.
The classic belt-drive family takes the 3363394 pump, in the $20–30 band. Later Whirlpool machines — and their Amana and Maytag siblings — moved to the direct-drive arrangement and take the 1515007/200937P pump instead, in the $40–55 band. Both listings name the machines they are listed for, so read the model sticker first, and if your model is not named, send it through before ordering and we will check.
The swap is honest Saturday-morning work. Unplug the machine, bail the water out, pull the machine clear of the wall and tip it for access. The pump sits at the motor — held by clips or a pair of screws depending on the era — with two hoses on spring clamps. Photograph the hose routing before you pull anything, keep a tray under the pump, and allow half an hour.
Fills then sits silent: the lid switch
This one fools people into calling time on the whole machine. The tub fills exactly as it should, then the machine goes quiet — no agitation, no spin, no noise. Or it washes normally but refuses to enter the spin. Nine times out of ten on this family that is the lid switch: a small plunger switch under the lid lip that tells the timer the lid is shut. Decades of lid-slamming eventually kill it.
Test it before you buy. With the machine unplugged, press and release the switch actuator and listen for the click; a dead switch often loses its click entirely. If you have a multimeter, check continuity across the switch with the lid closed — no continuity, no wash. The replacement for these machines is the 3949247 lid switch, the version with flat pins on the plug — check your plug matches before ordering. It sits in the $15–25 band and the swap is a screwdriver job.
One thing we will not help with: bypassing it. The lid switch is the only thing standing between fingers and a basket spinning at several hundred revolutions a minute. Never jam it, never magnet-cheat it — fit the switch. The full walkthrough, jiggle test included, is in our lid switch guide.
Barely agitates: the dogs and cam kit
The dual-action agitator on these Whirlpools is two parts: a lower half that swishes back and forth, and an upper auger that is supposed to ratchet one way only, feeding clothes down into the wash. The ratchet runs on four small plastic teeth — the agitator dogs. When they wear smooth, the top half free-spins in both directions, the clothes stop turning over, and everything comes out about as clean as it went in.
The test takes five seconds: grab the top half of the agitator and turn it by hand. Firm one way, ratcheting the other means the dogs are fine. Loose both ways means they are gone. The fix is the 285811 dogs and cam kit, in the $12–20 band: pop the cap on top of the agitator, undo the centre bolt with a socket on a long extension, lift the upper half clear and the four dogs sit in a ring underneath. Ten minutes, no tipping the machine. The long version — including how to tell worn dogs from a slipping belt or clutch — is in our agitator dogs and cam kits guide.
Timer knob split or free-spinning
The pull-to-start timer knob is the one part of these machines that gets a physical workout every single load, and after twenty years the plastic splines inside the knob strip on the timer’s D-shaft. The symptom is unmistakable: the knob turns and turns without the timer moving, or the skirt has cracked clean in half in your hand.
It is a push-on part and the swap takes about a minute. Two versions cover the family: the white 3364291 knob and the black 3956905 knob — pick the one that matches your console, both in the $12–30 band. If the timer itself will not advance even with a good knob, that is a different fault; send us the model number before spending anything.
Got the front-loader sibling instead?
If your Whirlpool is the Australian-built WFS-series front loader rather than the big top loader, the classic old-age failure is different: the machine fills and drains but the drum never turns, because the motor’s carbon brushes have worn down. That machine has its own article — our motor carbon brushes guide covers the WFS series alongside the other brushed-motor brands.
Fix it or replace it?
Run the numbers. Every part on this page sits in the $12–50 band. A tradie call-out and diagnosis typically runs $100–165 before any parts, and a new machine of comparable build quality is not a thing you can buy any more. These Whirlpools have steel where later machines have plastic, and their faults are the kind you can see and touch — which is exactly why so many are still washing.
The honest exceptions: a rusted-through outer tub or a dead transmission is the machine telling you it is done, and no $20–30 part changes that. For everything else, the washing machine parts store carries the wear parts that keep this family going.
Frequently asked questions
Where is the model number on a Whirlpool belt-drive top loader?
On the model sticker, usually under the lid or on the top rim of the cabinet; some machines carry it on the back panel. Photograph it before you order — every parts listing is matched against it.
How do I know which drain pump my machine takes?
By the model number on the sticker. The classic belt-drive family takes the 3363394 pump, while later Whirlpool, Amana and Maytag machines take the 1515007/200937P direct-drive pump. Both listings name the machines they cover; if yours is not named, send us the model number and we will check before you order.
Can I bypass the lid switch to keep washing while I wait for the part?
No. The lid switch is a safety interlock that stops the basket spinning with the lid open, and a top loader in spin has more than enough force to break an arm. Fit the 3949247 switch — it is a cheap part and a screwdriver job.
Do Amana and Maytag top loaders use the same parts as Whirlpool?
Often, yes — the three brands share platforms, and parts like the 1515007/200937P pump are listed for all of them. Never assume, though: match your model number against the listing, or send it through and we will confirm the right part.
Is a twenty-year-old top loader worth repairing?
Usually. The common failures — pump, lid switch, agitator dogs, timer knob — are all parts in the $12–50 band that swap with hand tools. The machine is only done when the outer tub rusts through or the transmission dies. Until then it is cheaper to feed it the odd part than to replace it.
Ready to order? Lift the lid, read the model sticker and search the part number above — or send the model number through our contact page and we will match the part before you pay. Get it to us by 12pm Sydney time and your part is dispatched from Sydney’s Northern Beaches the day you order.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
Appliance Spares

Wash finishes but the water just sits there
Won’t drain, and yours is a later machine (Whirlpool, Amana or Maytag)
Fills, then sits in silence — or washes but refuses to spin
Top half of the agitator flops or ratchets freely both ways
Timer knob spins without starting anything, or has split in half



