
Quick answer: The most common faults on the Samsung WF1752 and WF1804 front loaders are a leaking or mouldy door seal ($43.95), worn motor carbon brushes that stop the drum turning ($27.85 a pair), and worn drum bearings ($49.75 for the seal and bearings kit). A door locker that stops the cycle starting is $22.49. All are in-stock parts shipped fast from Sydney’s Northern Beaches.
Samsung 371201202 Washing Machine Motor Carbon Brush Pair WF1752WPW,WF1752WPC,WF1804WPCIn stock · Sydney warehouseView part
Samsung Washing Machine Door Seal WF1752WPC/XSA WF1752WPW/XSA WF1804WPC/XSA 0095In stock · Sydney warehouseView part
Samsung DC62-00008A Washing Machine Lip Seal & Bearings WF1804WPC WF1702XEC WD8704EJA 0164In stock · Sydney warehouseView part
Samsung Washing Machine Seal & Bearings Kit WF1752WPW,WF8802,WF9854 0164In stock · Sydney warehouseView part
Samsung Washing Machine Spider Shaft Flat Connector WF1752WPC/XSA WF1752WPW/XSAIn stock · Sydney warehouseView part
Samsung Washing Machine Water Pressure Sensor WF1804WPC/XSA, WF8750LSW/XSA 0866In stock · Sydney warehouseView part
Samsung Washing Machine Spider Shaft DC97-15185A WF1804WPY, WF1804WPC,WW80J5230GIn stock · Sydney warehouseView part
Genuine Samsung Washing Machine Drive Belt WF1104XAC WF1752WPC WF1752WPWIn stock · Sydney warehouseView part
Fit check: the model number on your sticker must appear in the listing title — the badge on the front is not enough. Photo the sticker and we find it, or send us the model number and we match it before you pay.
Door Seal (WF1752WPC / WF1752WPW / WF1804WPC) — $43.95 ·
Motor Carbon Brush Pair — $27.85 ·
Seal & Bearings Kit (WF1752WPW) — $49.75 ·
Door Locker — $22.49 ·
Spider Hex Bolts (3 pack) — $29.95 ·
Not sure which part? Use the Part Finder
Common faults on the Samsung WF1752 and WF1804
The Samsung WF1752WPC, WF1752WPW and WF1804WPC are front-load washing machines from the same platform, and they share their major wear parts — which is why every listing on this page covers the family rather than a single model. These machines use a brushed motor, so alongside the usual front-loader wear items (door seal, drum bearings, door locker) they have one fault the newer direct-drive Samsungs don’t: motor carbon brushes that wear down over years of use and eventually stop the drum turning altogether. The good news is that brushes are cheap, and a machine that suddenly stops turning its drum is very often a $27.85 fix.
Before ordering parts, locate the model sticker on the door jamb (the frame exposed when you open the door). Confirm the full model number — the WF1752 and WF1804 look very similar from the front, and several parts on this page also suit related Samsung front loaders, so the fitment list on each listing is the authority.
| Part | Symptom | Price | Link |
|---|---|---|---|
Door seal | Water leaking from the front of the machine during the wash; black mould embedded in the rubber folds; splits or perished patches in the boot | $43.95 | Buy door seal |
Motor carbon brush pair | Drum not turning while the machine otherwise runs; motor sparking or a burning smell after years of service; weak or intermittent drum rotation before stopping entirely | $27.85 | Buy carbon brush pair |
Seal + bearings kit | Loud grinding or rumbling during spin that worsens over time; drum play when rocked by hand; rust-coloured marks on washing | $49.75 | Buy bearing kit |
Door locker | Machine won’t start a cycle; door refuses to lock at the start or won’t release at the end; door-related error code on the display | $22.49 | Buy door locker |
Spider hex bolts (3 pack) | Replaced as a set whenever the drum spider is removed during a bearing repair; knocking from the drum if a bolt has let go | $29.95 | Buy spider hex bolts |
Diagnosis guide – Samsung WF1752 / WF1804
- Note any error code first. If the display is showing a code, write it down before attempting anything else. A door-related code points to the door locker; a motor code on a machine of this design often points to worn brushes. The code narrows the field immediately.
- Check whether the drum turns under power. If the machine fills and drains normally but the drum never rotates, worn carbon brushes are the prime suspect on this brushed-motor platform. Spin the drum by hand first — if it turns freely but does nothing under power, the brushes have almost certainly worn past their limit.
- Inspect the door seal closely. Fold back the rubber boot and check the folds and the lower six o’clock section where water pools. Splits, perished rubber or deep mould all mean replacement — embedded mould cannot be scrubbed out.
- Listen during a fast spin. A low grinding or rumble that rises with drum speed points to worn drum bearings, usually after the tub lip seal has let water into the bearing housing. Rock the inner drum by hand with the machine off — noticeable play confirms it.
- Test the door locker. Close the door firmly and press Start. If the machine never clicks the door locked and refuses to fill, the door locker has failed. It is one of the cheapest parts on the machine to replace.
Fitting the parts yourself
Carbon brushes are the signature repair on this family and one of the most rewarding: the motor comes out from under the tub after removing the rear panel, the two old brushes unclip from their holders, and the new pair slides in. Allow an hour including removal and refitting of the motor, and expect the machine to run a little noisily for the first few loads while the new brushes bed in to the commutator. The door seal and door locker are both front-of-machine jobs that need no special tools — the seal takes up to an hour with patience on the retaining band, the locker around half that.
Bearing replacement is the most involved repair on any front loader: the tub comes out and is split, the old bearings are pressed out, and the new lip seal is fitted. Allow 90 minutes to two hours, and replace the spider hex bolts at the same time since they are removed during disassembly. If you’d prefer a technician handled it, the kit price keeps the parts cost modest — only the labour varies.
Frequently asked questions
Why has my Samsung WF1752 or WF1804 stopped turning the drum?
On this brushed-motor platform, worn carbon brushes are the classic cause. They wear gradually over years of use until the motor loses contact and the drum simply stops turning, even though the machine fills and drains normally. A new pair is $27.85 and restores full drive.
Why is my machine leaking from the door?
The door boot seal perishes and grows mould with age, and once the watertight face against the glass is compromised the machine drips from the front during the wash. Our guide on Samsung washing machines leaking from the door seal covers the diagnosis in more depth.
What makes a WF1752/WF1804 loud on spin?
A grinding rumble that builds with drum speed is the classic sign of worn drum bearings. The seal and bearings kit above replaces the lip seal and both bearings in one job. Our guide on Samsung washing machines making a loud noise walks through the other causes worth ruling out first.
Where is the model sticker on these machines?
On the door jamb — the frame exposed when you open the washing machine door. It lists the full model number and serial number. Confirm the model number from the sticker before ordering parts.
Is a machine this age still worth repairing?
Usually, yes. Every part on this page is under $50, and the faults this platform develops — brushes, door seal, bearings, door locker — are all well-understood repairs with parts readily available. If the drum and electronics are healthy, a worn brush pair or door seal is not a reason to replace an otherwise solid machine.
Related
- Samsung washing machine leaking from the door seal — which part fixes it
- Samsung washing machine making a loud noise — 4 causes and fixes
- Browse all Samsung WF1752 parts
- Browse all Samsung WF1804 parts
- Part Finder Quiz — enter your model number for matched results
Ready to fix it?
- Locate the model sticker on your door jamb and confirm your full WF1752 or WF1804 model number.
- Note the fault or error code displayed on the machine.
- Select the matching part from the table above, or use the Part Finder if you’re unsure.
- Add to cart at ozappliancespares.com.au — orders placed before the daily cut-off ship same day from Sydney’s Northern Beaches.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
Appliance Spares








Door seal
Motor carbon brush pair
Seal + bearings kit
Door locker
Spider hex bolts (3 pack)



