Appliance Spares
Quick answer: If your Hisense front loader is leaking from the door, smells musty, or the rubber boot is torn or mould-stained, the fix is a new door seal (the door boot or gasket). The replacement seal costs $64.55, fits the WFEA 6010, WFU 6012 and HWFR6510, and takes about 45 to 60 minutes to fit yourself with basic hand tools. Unplug the machine first — the rest is patience with the retaining springs.
Find the right door seal for your model: Hisense washing machine door seal — $64.55 · find your model
What the door seal does
The door seal is the flexible rubber boot between the drum opening and the glass door. On a front loader the wash water sits at the bottom of the drum during a cycle, and the seal is the only thing keeping it inside the machine. It presses against the door glass to form a watertight ring every time the door shuts.
It leads a hard life. The rubber flexes on every spin, holds hot detergent water, and its inner fold is a permanent damp trap for lint, hair and stray coins. Over five to eight years the boot perishes, splits along the fold, or grows black mould that won’t wash out. Once it tears or hardens it stops sealing, and water finds its way onto the laundry floor.
Symptoms of a failed Hisense door seal
| Symptom | Likely cause |
|---|---|
| Water on the floor at the front during wash or spin | Split or perished seal, or debris trapped in the fold |
| Black or grey mould in the rubber folds that returns after cleaning | Mould has penetrated the rubber — clean first, replace if it persists |
| A visible tear, crack or hole in the boot | Seal has failed and must be replaced |
| Damp, musty smell from the drum | Trapped water and mould in the seal fold |
| Small items escaping under the seal | Boot no longer sitting flush against the door glass |
If the rubber is torn or the mould keeps coming back, the seal is finished. For a mould-only problem a thorough clean is worth trying first, but a torn boot only gets worse with use.
How to replace a Hisense door seal step by step
Safety: mains voltage — always unplug at the wall before opening the cabinet.
- Unplug the machine and turn off the water taps. Keep a towel and shallow tray ready; the seal fold holds trapped water.
- Open the door and find the outer retaining spring. The boot’s outer lip is held to the front panel by a spring band seated in a groove around the door opening.
- Release the outer spring. Locate the tension spring or clip join, lever it out with a flat screwdriver, and free the outer lip of the seal from the front panel all the way around.
- Fold the boot inward through the door opening to expose the inner clamp holding the seal to the drum tub.
- Release the inner clamp and pull the old boot off the tub lip. Note the top locating mark or drain hole so the new seal goes on the same way up.
- Clean the tub and panel lip so the new seal seats against a clean, dry surface.
- Fit the new seal onto the tub first, lining up the locating mark at the top, then refit the inner clamp.
- Seat the outer lip into the front-panel groove all the way around, then work the outer spring back into its groove evenly so the boot sits flat with no puckers or twists.
- Reconnect power and water, and run an empty rinse-and-spin. Watch for leaks before you wash a real load.
The retaining springs are the fiddly part. A boot fitted with a twist, or a lip not fully pushed home, is the usual reason a seal still leaks after fitting — so work slowly and check the boot sits flat all the way round.
Which seal fits my Hisense model
The replacement seal fits these Hisense front loaders:
- WFEA 6010
- WFU 6012
- HWFR6510
Your model number is on the model sticker inside the door frame or on the rear panel. If your Hisense isn’t listed here, use the part finder to confirm the correct seal rather than guessing — Hisense used more than one boot design across its front-loader range.
Door seal replacement cost in Australia
| Option | Estimated cost | Time |
|---|---|---|
| DIY seal replacement (part only) | $64.55 | 45–60 minutes |
| Tradie call-out + seal fitted | $200–$340 (labour + part) | 1–1.5 hours |
At $64.55 the part is the smaller part of a tradie’s quote — most of that bill is the call-out fee and labour. If you’re comfortable easing the retaining springs off and on, this is a straightforward DIY job.
Parts that fix this
In stock now and dispatched the same day from Sydney (order before 12pm). Not sure which one fits your model? Find your model number and match it against the fitment list on the part page before you order.
Frequently asked questions
Is this a genuine Hisense door seal?
This is a quality replacement seal made to fit the listed Hisense models. It does the same sealing job as the original boot at a lower price.
How do I know if the seal needs replacing or just cleaning?
If the leak or smell comes from mould and trapped debris, a thorough clean often fixes it. If the rubber is torn, cracked or hardened, cleaning won’t help — the seal has to be replaced.
Can I fit the seal myself?
Yes. It’s a hand-tool job with no electrical work once the machine is unplugged. The trickiest part is working the retaining springs off and back on evenly, so allow an unhurried hour.
Why does my Hisense seal keep growing mould?
Front loaders trap water in the seal fold. Leaving the door ajar between washes, wiping the fold dry and running a monthly hot cycle all slow mould down. Once mould has soaked deep into the rubber, replacement is the only lasting fix.
Will a new seal stop the leak completely?
If the leak was from a failed seal, yes — provided the new boot is seated evenly with the springs fully home. Run an empty rinse-and-spin first to confirm before washing a full load.
My model isn’t on the fitment list — what should I do?
Use the part finder with your exact model number. Confirming the correct boot is worth the minute it takes, since Hisense used several seal designs across its range.
Related
- Washing machine door seal replacement — complete guide
- Washing machine leaking from the door seal — how to diagnose it
- How to remove mould from a washing machine door seal
- Fisher & Paykel washing machine door seal replacement
- Haier TwinTasker washing machine door seal replacement
- Find the right part for your Hisense model
- Hisense door seals: which boot does your washer need?
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
