Appliance Spares
Quick answer: The Haier HWF75AW1 and HWF75AW2 are 7.5 kg front loaders on the same platform, and most wear parts are shared: the door seal, door lock, door hinge, spider arm and the lip seal and bearings kit are each listed for both models. A complete drum overhaul kit covers the worn-bearing rumble in one order, and the door interlock and heater element are stocked in versions listed for the HWF75AW2. Check the model sticker on the door jamb for your exact code, then match it against the listing before ordering — or photo the sticker and send it through the Oz Appliance Spares Part Finder.
Not sure which one fits? Match your model number or check the sticker inside the door.
In-stock parts for the HWF75AW1 and HWF75AW2:
- Door seal gasket — listed for HWF75AW1, HWF75AW2, HWF75DW1, HWF80BW1, HWF80BW2
- Drum overhaul kit (bearings, belt, door seal) — listed for HWF75AW1 and HWF75AW2
- Lip seal and bearings kit — listed for HWF75AW1, HWF75AW2, HWM70-1201
- Spider tripod assembly — listed for HWD8040BW1, HWF75AW1, HWF75AW2, HWF75AW3
- Door hinge — listed for HWF10BW1, HWF75AW1, HWF75AW2, HWF75DW1, HWF75SW2
- Door lock — listed for HWF10BW1, HWF75AW1, HWF75AW2, HWF75DW1, HWF80BW1
- Door interlock — listed for HWF75AW2, HWF85AW2
- Heater element — listed for HWM80-1403D, HWF75AW2
AW1 or AW2 — read the sticker first
These two machines look the same in a laundry and share most of their platform, which is why several listings above carry both codes. The difference still matters at the edges: the door interlock and the heater element stocked here are listed for the HWF75AW2, so AW1 owners with a locking or heating fault should confirm through the Part Finder before ordering those two rather than assuming crossover.
The model sticker sits on the door jamb — open the door and check the frame around the rim, usually near the 3 or 9 o’clock position, with a duplicate data plate on the rear panel on most machines. Note the full code: HWF75AW1 and HWF75AW2 are what this page covers. If your sticker instead reads HWF75AN1 or HWF85AN1, those are a different platform — use the Haier model number guide to decode what you are seeing.
Symptom to part — HWF75AW1 / HWF75AW2
| Symptom | Likely part | The listing covers | Link |
|---|---|---|---|
 Water leaking at the front during the wash; mould or splits on the rubber boot | Door seal gasket | HWF75AW1, HWF75AW2, HWF75DW1, HWF80BW1, HWF80BW2 | View door seal |
 Rumble or grind on spin that keeps getting louder; play in the drum | Drum overhaul kit, or the lip seal and bearings kit alone | HWF75AW1, HWF75AW2 (kit); HWF75AW1, HWF75AW2, HWM70-1201 (bearings) | View overhaul kit |
 Loud banging on spin after a bearing failure ran too long; cracked drum support | Spider tripod assembly | HWD8040BW1, HWF75AW1, HWF75AW2, HWF75AW3 | View spider assembly |
 Door drooping, rubbing on the cabinet, or leaking because it no longer sits square | Door hinge | HWF10BW1, HWF75AW1, HWF75AW2, HWF75DW1, HWF75SW2 | View door hinge |
 Door will not latch, or the handle no longer catches | Door lock | HWF10BW1, HWF75AW1, HWF75AW2, HWF75DW1, HWF80BW1 | View door lock |
 Door latches but the cycle never starts; door light flashing | Door interlock (electrical) | HWF75AW2, HWF85AW2 | View door interlock |
 Warm cycles washing cold | Heater element | HWM80-1403D, HWF75AW2 | View heater element |
Diagnosing the common faults
- Leak at the front. Inspect the lower fold of the door seal where water sits between washes. Splits and mould damage mean replacement. If the seal looks sound, close the door slowly and watch whether the glass presses evenly all the way around — a sagging hinge leaks through a good seal.
- Noise on spin. Spin the empty drum by hand. A dry rumble is the bearings; a clunk with visible drum movement when you rock the paddle is bearings or, if it has been left a long time, the spider arm behind the drum. The overhaul kit exists because by the time the bearings scream, the belt and door seal are usually due as well.
- Door problems. Mechanical faults first: does the door physically catch when pushed shut? If not, the lock or hinge is the problem. If it latches firmly but the machine will not start and the door light flashes, the electrical interlock is not confirming the latch, which is a separate part.
- Washing cold. Feel the door glass twenty minutes into a warm cycle. Cold glass means the element or its sensor. The element is reached from the rear panel with the machine unplugged.
Fitting the parts yourself
Door seal, lock, interlock and hinge are all front-of-machine repairs that most careful DIYers can do in under an hour with the machine unplugged and the taps off. Photograph wiring before disconnecting anything. The bearings, spider and overhaul kit are a half-day job that involves splitting the tub — very doable on this platform, but read the process end to end before you start. Our guide to replacing a Haier door seal shows the seal technique step by step.
Sticker faded or missing?
Photograph whatever is left of the sticker and send it through the Part Finder — a partial code is normally enough to separate an AW1 from an AW2. The purchase receipt or manual records the model too, and once you have the code the Find Your Model tool takes you straight to matched parts.
FAQ
Are HWF75AW1 and HWF75AW2 parts interchangeable?
Mostly. The door seal, door lock, hinge, spider and bearings kit here are each listed for both models. The exceptions on this page are the door interlock and heater element, which are listed for the HWF75AW2 — AW1 owners should confirm those through the Part Finder before ordering.
Why is my Haier HWF75AW2 not starting with the door closed?
If the door latches firmly but the cycle will not begin, the door interlock is the usual suspect — it is the electrical switch that tells the board the door is locked. If the door will not physically latch at all, look at the door lock and hinge instead.
What causes a loud rumbling spin on these machines?
Worn drum bearings. Left long enough, the movement can also damage the spider arm that carries the drum. If the noise has been building for months, price the overhaul kit rather than the bearings alone, since it includes the belt and door seal that are commonly worn by the same point.
Do HWF75DW1 or HWF80BW1 owners use these parts?
Some of them: the door seal, hinge and lock listings on this page name those models too. Match your exact sticker code against the listing, and if it is not shown, run it through the Part Finder rather than assuming the fit.
Is a 7.5 kg Haier front loader worth repairing?
For seal, lock, hinge and pump-level faults, almost always — the parts are inexpensive and the jobs are quick. A full bearing and spider failure on a machine that has also rusted or damaged its cabinet is the point where replacement starts to compete.
Related
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
