Appliance Spares
Quick answer: The Omega OCD40WA and the Euromaid DM4KG and ED45KG vented dryers are the same machine wearing different badges, so they share the same two service parts: a clip-in filter grille outlet on the lint path and a drum belt on the drive. Both are jobs most people can do at home — the grille needs no tools at all, the belt needs a screwdriver and half an hour — and both are matched by the model code on your model sticker, not by the brand on the door. Here is which part does what, how each one fails, and how to fit them.
Last updated August 2026
One dryer, several badges
These compact vented dryers share one platform and were sold in Australia under more than one brand name. The Omega OCD40WA and the Euromaid DM4KG and ED45KG use the same cabinet, drum and drive layout, so you match the model code, not the badge, and one grille and one belt cover all three.
447 of the parts we document fit ten or more appliance models each, and 60 fit fifty or more. Shared platforms like this one are the reason why. The table below is the whole parts story for these three codes:
| Part | Part number | Fits | Order it |
|---|---|---|---|
 Filter grille outlet | — | OCD40WA, DM4KG, ED45KG | Genuine Omega and Euromaid dryer filter grille for OCD40WA, DM4KG and ED45KG |
 Drum belt | 4PH1950 | OCD40WA, DM4KG, ED45KG | Omega and Euromaid dryer drum belt for OCD40WA, DM4KG and ED45KG |
If you want the wider picture of the platform — what else these machines share and how the family hangs together — start with Euromaid and Omega dryer parts in Australia. This guide stays on the two parts above.
The filter grille: small part, expensive habit
A vented dryer pushes hot, damp air out of the drum, and all of it has to pass through the lint filter on its way to the outlet. On this platform the filter seats into a plastic filter grille outlet in the door opening — the frame that holds the filter flat in the airstream. It cops the heat of every cycle plus the knock of every load going in and out.
It fails the way heat-cycled plastic fails: the locating tabs go brittle and snap off, or the frame warps until the filter no longer sits flush. The symptoms:
- The filter will not click home, or falls out when you open the door.
- Lint where it should not be — packed around the door rim, sitting in the outlet duct, or drifting back onto clothes.
- A plastic rattle or buzz during the cycle from a grille that is loose in its housing.
- Visible cracks or missing tabs on the grille itself.
None of these stop the dryer, which is why the part gets ignored for months. Do not leave it. Lint that slips past a badly seated filter builds up in the outlet and duct, where the airflow narrows and the air is hottest. A restricted lint path stretches every cycle out — the running-cost basics for dryers are laid out at energy.gov.au — and built-up lint near a heat source is the classic dryer fire risk Product Safety Australia warns about. A grille is the cheap end of that equation.
The drum belt: motor runs, drum stands still
The belt is a long, thin loop that wraps right around the drum and down to the motor pulley. When it snaps or jumps off, the motor keeps running but the drum stops. The classic presentation: you press start, the motor hums away behind the panel, and the clothes just lie there in a damp heap.
Three quick checks before you order anything:
- Turn the drum by hand with the door open and the power off. An intact belt drags the motor around, so the drum turns with springy resistance; a drum that freewheels has a snapped or thrown belt.
- Listen at the start of the cycle. A squeal or rhythmic slap that fades as the machine warms up is a glazed or fraying belt slipping on the pulley — replace it before it lets go entirely.
- Check the load at the end. A belt failure leaves clothes cold, wet and in the same position you loaded them.
Two look-alike faults are worth ruling out. If the motor only ever hums and never spins up, a tired run capacitor produces the same soundtrack — testing the run capacitor takes ten minutes. And if the drum turns but the air never gets warm, the drive side is healthy — that is heating-element territory, with its own guide for this platform: Omega and Euromaid dryer not heating — the element you need.
Fitting the filter grille
- Switch the dryer off at the power point.
- Pull the lint filter out of the old grille, then unclip the grille from the door opening. Broken tabs usually mean it comes out in pieces — collect them all, because loose plastic ends up in the fan.
- Compare old and new side by side: same outline, same tab positions.
- Click the new grille home, seat the filter in it, and check the filter sits flat with no gaps around the edge.
Two minutes, no tools, and the lint path is sealed again. While you are there, vacuum the outlet behind the grille — whatever lint got past the old one is still sitting in the airway.
Fitting the drum belt
Budget half an hour and keep a phone handy for photos.
- Unplug the dryer and move it somewhere you can reach the back and top panels.
- Remove the cabinet panels to expose the drum and motor. Panel screws on this style of dryer sit around the rear edge — keep them sorted, because reassembly is the fiddly half of the job.
- Photograph the belt routing before you disturb anything. The belt runs around the drum with its ribbed side against the drum surface, then loops down under a tensioner beside the motor pulley — the photo saves guessing later.
- Slip the old belt off, loop the new one around the drum in the same position, and work it onto the motor pulley and tensioner following your photo.
- Rotate the drum by hand two full turns. The belt should track flat and central, without walking towards either edge.
- Refit the panels, plug in and run a short empty cycle — smooth and quiet means the tension is right.
Do it yourself or call a tradie?
The grille is a no-tools job for anyone. The belt is a genuine do-it-yourself repair, with caveats:
- For doing it yourself: no wiring is disturbed, the part is cheap relative to a call-out, and the only skills involved are removing panels and routing a belt from a photo.
- Against: cabinet edges are sharp, reassembly is tedious, and if the drum bearings or tensioner are worn the new belt will not run true — a squeal that returns within weeks means more than a belt.
- Call a tradie if the drum grinds or drops on its bearing when you turn it by hand, if the machine trips the safety switch, or if you open the back and find the belt intact — at that point you are diagnosing, not replacing.
Frequently asked questions
Where is the model number on an Omega or Euromaid dryer?
On the model sticker, usually inside the door opening on the rim of the cabinet, or on the back panel. You are looking for a code like OCD40WA, DM4KG or ED45KG. Photograph it before ordering — the code, not the brand, decides the part.
Are Omega and Euromaid dryer parts interchangeable?
For these three models, yes — OCD40WA, DM4KG and ED45KG are the same machine under different badges, and the grille and belt in the table above fit all three. Do not extend that logic to other models in either range without checking the code first.
The motor hums but the drum will not turn. Is that always the belt?
Usually, but not always. Turn the drum by hand first: freewheeling with no resistance points at the belt. If the belt is intact and the motor still only hums, suspect the run capacitor before you condemn the motor.
Can I keep using the dryer with a cracked grille while the part arrives?
You can, but vacuum the filter area every load, because lint is bypassing the filter into the hot side of the airway. If the grille is missing or shattered, wait for the part — an unfiltered lint path is how ducts end up packed solid.
Why does the lint filter keep falling out?
The filter is almost never the culprit — the grille it clips into is. Snapped locating tabs or a heat-warped frame stop the filter seating, and no amount of pushing fixes brittle plastic. Replace the grille.
The drum turns but everything comes out cold and damp. Is the belt on its way out?
No — a turning drum means the belt is doing its job. Cold air points at the heating side of the machine, which is covered in the element guide linked above rather than here.
Get the right part first time
Check the code on your model sticker, then run it through the part finder — or send us the code and we will confirm the match before you pay. Orders placed before 12pm are dispatched the same day from Sydney’s Northern Beaches.
Disclaimer: this article is general information only and is provided without warranty of any kind. Appliance designs vary between models and production runs — always follow the manufacturer’s instructions, switch off and unplug the appliance before starting any work, and confirm parts against the model number on your appliance’s model sticker. Any repair is undertaken at your own risk and Oz Appliance Spares accepts no liability for injury, loss or damage arising from work performed after reading this guide, to the maximum extent permitted by law. If in doubt, use a qualified technician.
